BendPak 5175153, Service Manual

Page: 27 / 40

11
3
10
4
7
8
14
5
15
13
2
17
12
16
18
19
6
9
20
21
1
22
ISOMETRIC VIEW
FOR REFERENCE ONLY
DO NOT SCALE
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
G
5735741 WAS 153 NOW 134, UPDATED
BOM REVISION
07/31/2014 TM 00664
H
H-001
H-002
REMOVED 5735038
ADDED RAL NUMBER TO NOTES
ADDED GLOSS NOTE TO PAINT, REMOVED
GRIT NOTE
03/25/2016
02/22/2017
02/05/2020
TM
TS
CA
00741
00811
01120
J
REPLACED 5700647 WITH 5700409 AND
5735032 WITH 5735688, ADDED 5735851,
UPDATED NEXT ASSEMBLIES
02/23/2021 CA 01276
ITEM
NO
PART
NUMBER
DESCRIPTION QTY REV
1 5701075 HDS/HDSO-14 POWER SIDE RAMP 1 B
2 5620246 HDS/HDSO-14 SERIES END PLATE WELDMENT 2 B
3 5700409 HDS/HDSO-14 ROLLING BRIDGE BEAM 1 A
4 5700139 HDS-14 TURNPLATE SUPPORT CHANNEL 1 B
5 5730038 HDS-14LSX/LSXE RAMP CASTER PLATE 1 A
6 5731035 HDS/HDSO-14 FRONT RAMP SUPPORT PLATE 1 A
7 5731020 HDS/HDSO-14 REAR RAMP SUPPORT PLATE 1 A
8 5731623 HDS/HDSO-14 REAR RAMP AIR SUPPORT PLATE 1 A
9 5731036 HDS/HDSO-14 FRONT RAMP AIR SUPPORT PLATE 1 A
10 5735026 D4-12/HD/HDSO-14 TIE BAR 1 E
11 5735688 D4/GP-9/HDS/HDSO-14 RAIL END CAP 2 A
12 5735084 HDS-14 CYLINDER SUPPORT PLATE 1 A
13 5736161 HDS-14 RAMP SHEAVE BOTTOM PLATE 2 B
14 5736165 HDS-14LSX CYLINDER MOUNTING PLATE 1 A
15 5746096 HDS-14 BOTTOM SPACER, RAMP SHEAVE 2 A
16 5700012 HOSE RETAINER 14 B
17 5755709 D4-12, HDS-14LSX/LSXE CASTER RETAINER 30 A
18 5746148 SLIP PLATE LOCK TUBE 4 A
19 5735741 HDS-14L SERIES SKID PLATE 1 B
20 5731628 HDS-14 SLIP PLATE GUSSET 5 A
21 5735352 SINGLE CLEVIS CYLINDER ALIGNMENT PLATE 1 A
22 5735851 HDS/HDSO-14 RAMP SUPPORT STRAP 2 A
WHERE USED
HDS-14LSX
HDSO-14AX
NEXT ASSEMBLY
5216019
5216021 SHEET 1 OF 4
REV DWG. NO.
A
SIZE
TITLE:
NAME DATE
CHECKED
DRAWN
J
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
GJZ
5600186
HDS/HDSO-14 POWER SIDE
RAMP WELDMENT
11/19/2008
DO NOT SCALE DRAWING
1:30 SCALE:
THIRD ANGLE PROJECTION
OR 03/01/2021
DIMENSIONS ARE IN MM
TOLERANCES:
0. = ±1.5
0.0 = ±0.5
SURFACE FINISH 1.6 ISO Ra µm
FOR MACHINED SURFACES
UNLESS OTHERWISE SPECIFIED
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
BREAK AND DEBURR ALL SHARP EDGES 0.3mm 2.
REMOVE ALL WELD SPLATTER 3.
DIMENSIONS SHOWN ARE AFTER PAINTING 4.
PAINT GRAY (RAL-7024) 20% GLOSS 5.
NOTE: UNLESS OTHERWISE SPECIFIED.