background image

 

FlightSim Developers 

 

 

KFC 225 Autopilot 

Pilot Handbook 

 

- 20 – 

For use with Microsoft Flight Simulator only. Not to be used in real world aviation. 

 

 

Takeoff from Runway 8 and turn to 120° 

Climb to 6,000 Feet 

Takeoff from Runway 8 and Enter 20° Right 

Turn - Climb at 600 Feet Per Minute 

 

 

 

 

 

 

 

A.  Aircraft departs runway 8. Establish a safe 

climb rate, and then turn the heading bug on 

the HSI to 80° (runway heading). 

 

Select 6,000 feet on the Preselector Knob, and 

then press the ALT Key. This will establish the 

aircraft in a steady climb to 6,000 feet. 

 

Press the HDG Key and the AP Master key to 

switch the KFC225 to Heading Hold Function 

and 

Active Mode

. 

B.  Turn the HSI heading bug to 120° 

C.  The aircraft turns to the selected heading 

 

A.  Aircraft departs runway 8. Establish a safe climb 

rate. Ensure that the FD Key is depressed and 

illuminated. ROL and PIT will be displayed. 

 

Press the center of the Preselector Knob to 

change the control to Roll Select. The ROL 

display will temporarily turn green. Select a 20° 

right turn. 

B.  Press the VS Key and the PIT display will 

indicate FPM. Use the UP key to select 600 FPM. 

Then, press the AP Master Key to switch the 

KFC225 to 

Active Mode

. 

C.  The aircraft will climb at 600 FPM, and maintain 

a right hand turn of 20°. 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for KFC225


























Reviews: