background image

 

FlightSim Developers 

 

 

KFC 225 Autopilot 

Pilot Handbook 

 

- 19 – 

For use with Microsoft Flight Simulator only. Not to be used in real world aviation. 

 

2. Detailed System Operation 

 

The following represents the detailed operating instructions and control sequences necessary to 

operate the KFC225 in all phases of flight. 

 
2.1 BASIC PROCEDURES 

Takeoff and climb to 9,200 feet. 

 

 

 

 

 

 

 

A.  Aircraft departs runway 8 and established a 

safe climb rate. The heading bug on the HSI 

is turned to 80° (runway heading). 

 

Press the HDG Key and the AP Master key 

to switch the KFC225 to Heading Hold 

Function an

Active Mode

. 

B.  Press the VS Key and use the UP Key to set 

the pitch axis to 700 FPM climb. 

 

Rotate the Preselect Control to change the 

Altitude Preselect to 9,200'. Press the ARM 

key. 

 

C.  When the aircraft reaches 8,200 feet 

indicated altitude the Altitude Alert will 

flash for two seconds, and a 3 tone aural 

annunciation will occur, indicating that the 

aircraft is approaching the preselected 

altitude. 

 

At 9,000 feet indicated altitude the alert 

will occur again, signaling 200 feet from 

altitude capture. 

D.  At 9,200 feet the ALT light illuminates, 

switching the KFC225 to ALT Mode and the 

aircraft maintains 9,200 feet. 

 

 

 

 

Summary of Contents for KFC225


























Reviews: