manualshive.com logo in svg

BENDIX EC-60 ABS, Service Data

Share
Download
BENDIX EC-60 ABS Service Data Download Page 30

30

Troubleshooting Diagnostic Trouble Codes:

Pressure Modulator Valves

 7 

Left Steer Axle 

 8 

Right Steer Axle 

 9 

Left Drive Axle 

 10 

Right Drive Axle 

 16 

Left Additional Axle 

 17 

Right Additional Axle 

 

20

 

Trailer PMV

1st .  Blink

Code

Location

2nd . 

Blink 

Code

Diagnostic 

Trouble Code 

Description

Repair Information

1

Release   Solenoid  

Shorted to 

Ground

Verify no continuity between PMV leads and ground.  Verify 4.9 to 5.5 ohms from REL 

to CMN & HLD to CMN, and 9.8 to 11 ohms from REL to HLD.  Check for corroded/

damaged wiring or connectors between ECU and PMV.

2

Release   Solenoid 

Shorted  to 

Voltage

Verify no continuity between PMV leads and voltage.  Verify 4.9 to 5.5 ohms from 

REL to CMN & HLD to CMN, and 9.8 to 11 ohms from REL to HLD.  Check for 

corroded/damaged wiring or connectors between ECU and PMV.

3

Release   Solenoid 

Open Circuit

Verify 4.9 to 5.5 ohms from REL to CMN & HLD to CMN, and 9.8 to 11 ohms from REL 

to HLD.  Check for corroded/damaged wiring or connectors between ECU and PMV.

4

Hold Solenoid 

Shorted to 

Ground

Verify no continuity between PMV leads and ground.  Verify 4.9 to 5.5 ohms from REL 

to CMN & HLD to CMN, and 9.8 to 11 ohms from REL to HLD.  Check for corroded/

damaged wiring or connectors between ECU and PMV.

5

Hold Solenoid 

Shorted to 

Voltage

Verify no continuity between PMV leads and voltage.  Verify 4.9 to 5.5 ohms from 

REL to CMN & HLD CMN, and 9.8 to 11 ohms from REL to HLD.  Check for corroded/

damaged wiring or connectors between ECU and PMV.

6

Hold Solenoid 

Shorted to Open 

Circuit

Verify 4.9 to 5.5 ohms from REL to CMN & HLD to CMN, and 9.8 to 11 ohms from 

REL to HLD.  Check for corroded/damaged wiring or connectors between the ECU 

and PMV.

7

CMN Open 

Circuit

Verify 4.9 to 5.5 ohms from REL to CMN & HLD to CMN, and 9.8 to 11 ohms from 

REL to HLD.  Check for corroded/damaged wiring or connectors between the ECU 

and PMV.  Potentially a miswired or internal mechanical problem.

8

Configuration 

Error

A mis-match exists between the ECU configuration and the modulator installation 

and wiring.  Verify PMV wiring and installation.  Verify ECU configuration.  Special 

Note regarding Trailer PMV:  Pneumatic issues can result in this DTC being set.  

Verify all lines are free from debris or other obstructions, kinks, etc.

Summary of Contents for EC-60 ABS





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands