background image

Customer Service Email: [email protected]

P

hone:866-552-2810 

GC-MBLK66-ESP-GG/GC-MBLK66-GY-GG

Thank you for your purchase!

ASSEMBLY

 

INSTRUCTIONS

Before You Begin:

Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the 

components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching during 

assembly.

Tighten all components securely before use. Failure to do so may result in personal injury.

DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may result.

CHOKING HAZARD

 - Small Parts. Adult Assembly Required.

DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE

Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where 

included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The tipping 

restraint is intended only as a safety measure, it is not a substitute for proper adult supervision. 

To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall Straps 

suitable for the unit weight and wall materials (if not included) should be purchased and installed.

Online Assembly Instructions: 

http://ftp.flashfurniture.com/AssemblyInstructions/GC-MBLK66-

GY

-GG.pdf

Assembly Time

Load Bearing

60

 min

LBS

LBS

LBS

200 LBS

LBS

LBS

LBS

LBS

30 LBS

LBS

LBS

LBS

6 Cubby 65" TV Stand for up to 80" TV's

Summary of Contents for GC-MBLK66-ESP-GG










Reviews: