background image

     Thank you for your purchase!

 

AL-DM0201-TXL-GG / AL-DM0201-F-GG / AL-DM0201-Q-GG / AL-DM0201-K-GG 

Before You Begin:

 

Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the 

components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching 

during assembly. 

Caution:

 

Tighten all components securely before use. Failure to do so may result in personal injury. 

DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may 

result. 

Warning: 

CHOKING HAZARD

 - Small Parts. Adult Assembly Required. 

DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE 

Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where 

included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The 

tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.  

To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall 

Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.

Motorized Adjustable

 

Bed Base Frame

 

Customer Service Email: 

[email protected]

 | Phone: 866-552-2810

Summary of Contents for AL-DM0201-F-GG











Reviews: