17
16
CZ
DE
DK
EN
ES
FI
FR
GR
HU
IT
NL
NO
PL
PT
SE
APP
When you want to return to listening to the signal source connected to the External sound
source input (1), release the
a
button (6). The internal microphone is then disconnected and the
external sound source returns to normal volume again.
Clip
Remove the clip by using
the small round handles and
pressing out from the sides.
Place the clip against the battery cover and press firmly so that it locks on.
Indicators and settings
Volume and Tone LED Indicator
The Volume and Tone LED Indicator (8) is used as an indicator for the volume and tone con-
trols.
The Volume and Tone LED Indicator goes out after about 3 seconds to save power.
Low battery LED
The Low battery LED (11) is normally off, but comes on when the battery level falls below
about 10 hours’ remaining operating time. This time depends, of course, on the sound volume
and type of listening accessories used.
When the Low battery LED (11) blinks every seven seconds, the batteries should be replaced
with new ones. Only use AA alkaline type batteries.
Volume control
Maxi has a digital volume control
bc
(9), which means that you can increase or reduce the
volume with the pushbuttons
bc
(9). Each press results in an increase or reduction in volume
by one increment.
If you hold one of the volume buttons down for more than 1 second, the volume will increase or
reduce by one increment per second as long as the button is held down or until the minimum or
maximum position is reached.
By pressing the
c
button (9), the volume is increased by one increment at a time until the maxi-
mum volume is reached. At full volume all the LEDs of the Volume and Tone LED Indicator (8)
are illuminated.
By pressing the
b
button (9), the volume is reduced by one increment at a time until the mini-
mum volume is reached, although Maxi never becomes totally silent. At minimum volume only
the left LED of the Volume and Tone LED Indicator (8) is illuminated.
Tone control
BE2020 has a digital tone control
fg
(10), which means that you can increase or reduce the
treble with the pushbuttons
fg
(10). Each press results in an increase or reduction in treble by
one increment.
If you hold one of the tone buttons down for more than 1 second, the treble will increase or
reduce by one increment per second as long as the button is held down or until the minimum or
maximum position is reached.
By pressing the
g
button (10), the treble is increased by one increment at a time until maxi-
mum treble is reached. At maximum treble, the LED at the far right of the Volume and Tone
LED Indicator (8) is illuminated.
By pressing the
f
button (10), the treble is reduced by one increment at a time until minimum
treble is reached. At minimum treble, the LED at the far left of the Volume and Tone LED
Indicator (8) is illuminated.
When the centre LED of the Volume and Tone LED Indicator (8) is illuminated, treble is deac-
tivated.
Troubleshooting in brief
Symptom
Solution
Nothing happens when you try to start Maxi
using the On/Off button.
• Change the batteries. Only use AA alka
-
line type batteries.
No sound can be heard in the headphones
when Maxi is switched on.
• Check that the correct signal source has
been selected, e.g. internal microphone
(M position).
For further information about the product in English, refer to the Appendix.
1.
External sound source input 2.5 mm tele
jack
2.
Internal microphone
3.
Microphone LED
4.
Telecoil LED
5.
On/Off button
h
6.
Microphone Selection Button
a
7.
Telecoil Selection Button
d
8.
Volume and Tone LED Indicator
9.
Volume control
bc
10. Tone control
fg
11. Low battery LED
12. Headphone output 3.5 mm tele jack
13. Neck strap attachment
14. Battery compartment
15. Setting button
16. Battery cover lock
17. Battery cover
18. Clip
