background image

 

 

Installation 

WARNING! 

Please follow the points below when installing the appliance 
 

Use an Authorized Person 

  As  stated  in  the  local  municipal  building  codes 

and other relevant statutory regulations: 

  Wiring  connections  must  be  in  accordance  with 

AS/NZS  3000  Wiring  Rules  and  any  particular 
conditions of the local authority. 

  Refer  to  data  plate  for  rating  information.  The 

data plate is positioned at the side of cavity. 

  A functional switch should be provided near the 

appliance  in  an  accessible  position.  Refer  to 
AS/NZS 3000 clause 4.7.1. 

  Wiring  should  be  protected  against  mechanical 

failure. Refer to AS/NZS 3000 clause 1.5. 

  A  means  of  disconnection  with  a  contact 

separation  of  at  least  3mm must  be  supplied  in 
the fixed wiring. 

  Disconnect the power plug of the appliance from 

the  power  point  when  conducting  maintenance 
or repairs to the unit 

 

 

This Appliance Must Be Properly Earthed 

  Do not lift the appliance by the door handles. 

  Prepare  the  cupboard  opening  to  match  your 

appliance measurements. (See diagrams). 

  Slide appliance in to cabinet cavity, ensuring 

supply cable is not obstructed (kinked, jammed 
or twisted). 

  To prevent tipping or dislodging of the appliance, 

secure  appliance  to  the  cabinet  with  2  screws 
(provided),  through  the  dedicated  holes  in  the 
appliance frame. 

  Where  the  appliance  is  built  into  a  cabinet,  the 

cabinet material must be capable of withstanding 
120°C. Installation into low temperature tolerant 
cabinetry  (E.g.  vinyl  coated)  may  result  in 
deterioration  of  the  low  temperature  coating  by 
discoloring or bubbling. 

  The  cabinet  panels  to  the  oven  must  be  heat 

resistant. With veneered wood units, glues must 
be resistant to a temperature of 100

C. 

  If the appliance is to be installed adjacent to vinyl 

wrapped  surfaces,  use  an  installation  kit 

available from the vinyl-wrap supplier. 

  GSM  cannot  accept  responsibility  for  damage 

caused  by  installation  into  low  temperature 
tolerant cabinets. 

  After  installation,  test  and  ensure  the  appliance 

operates  correctly  before  handing  it  over  to  the 
customer.

 

CAUTION! 

Where  the  appliance  is  connected  via  power  supply 
cable to a power point, the installed power point must 
remain accessible after appliance installation 
A dedicated power circuit is recommended for the unit 
but  not  required.  Additional  electrical  appliances  on 
the same circuit may exceed the current (amperage) 
rating  for  that  circuit.  If  after  the  installation  of  your 
unit  the  circuit  breaker  trips  or  the  fuse  fails  on  a 
repeated basis, then a dedicated circuit will likely be 
required. 

WARNING! 

To  avoid  any  potential  hazard,  you  must 
follow  our  instructions  when  you  install 
your  appliance.  Failure  to  install  the 
appliance  correctly  could  invalidate  any 
warranty  or  liability  claims  and  lead  to 
prosecution. 

 

Install the shelf 

 

1.  Pay attention to high temperature, you may need 

to wear gloves if it is hot inside. 

2.  Always slide shelves into the layer with stopper. 

 
 

6

Summary of Contents for BOM609CX

















Reviews: