Bell System bellswipe Manual Download Page 21

Page: 21 / 21

bell

swipe

Card Access System

Specification

CR500 Control Unit

Dimensions

215 mm (H) x 200 mm (W) x 70 mm (D)

Power Consumption

32VA max. @ 230V~ +10% 50Hz

Output( C + & H -)

13.8V DC @ 200mA max.

Lock outputs

Fail-secure or Fail-safe

Undedicated relay

contact

13.8V DC @ 0.5A max.

connections: 1 pole changeover

(Voltage free)

switching current **1A @ 30VDC max.

Lock release time

1 - 250 seconds

Exit Input

Normally open contact (must be voltage free)

Time input

Normally open or closed contact (must be voltage free)

**protection must be added for Inductive loads, if used .

RH10 Card Reader

Dimensions

111 mm (H) x 38 mm (W) x 36mm (D)

Length of captive cable

2 m

Consumption

13.8V DC @ 40 mA maximum

Standards

This Product complies with European Directives:

89/336/EEC for Electro-Magnetic Compatibility (EMC)

73/23/EEC for Low Voltage Systems (LVD)

Made in the United Kingdom

Summary of Contents for bellswipe






















Search results

Summary of Contents for bellswipe

Reviews:

Related manuals for bellswipe

Brands by name

Popular brands

Bell System bellswipe, Manual

Search results

Summary of Contents for bellswipe

Reviews:

Related manuals for bellswipe

Brands by name

Popular brands