Bell and Gossett e-80SC Series Instruction Manual Download Page 6 | Manualshive

Page: 6 / 32

background image

All series e-80SC Pumps

All series e-80SC with optional ITSC/IT

P70643

P70644

P70642

EYEBOLTS OR LIFTING

LUGS IF PROVIDED ARE

FOR LIFTING ONLY THE

COMPONENTS TO WHICH

THEY ARE ATTACHED.
FAILURE TO FOLLOW

INSTRUCTIONS COULD

RESULT IN INJURY OR

DEATH.

DO NOT RUN PUMP DRY.

SEAL DAMAGE MAY OCCUR.
INSPECT PUMP SEAL

REGULARLY FOR LEAKS.

REPLACE AS REQUIRED.
FOR LUBRICATION

REQUIRMENTS, CONSULT

SERVICE INSTRUCTIONS.
FAILURE TO FOLLOW

INSTRUCTIONS COULD

RESULT IN INJURY OR

PROPERTY DAMAGE.

ROTATING COMPONENTS

DISCONNECT AND LOCK

OUTPOWER BEFORE

SERVICING.
DO NOT OPERATE WITHOUT

ALL GUARDS IN PLACE.
CONSULT INSTALLATION

AND SERVICE INSTRUCTION

SHEET BEFORE OPERATING

OR SERVICING.
FAILURE TO FOLLOW

INSTRUCTIONS COULD

RESULT IN INJURY OR

DEATH.

S11547

ELECTRICAL SHOCK HAZARD.

TURN OFF AND LOCKOUT ALL

POWER SOURCES PRIOR TO

SERVICING PANEL.
FAILURE TO FOLLOW THESE

INSTRUCTIONS COULD RESULT

IN SERIOUS PERSONAL INJURY,

DEATH, AND/OR PROPERTY

DAMAGE.

WARNING

Make sure that all safety instruction decals are always clearly visible and readable.

1.2.3 User safety

General safety rules

These safety rules apply:

• Always keep the work area clean.
• Pay attention to the risks presented by gas and vapors in the work area.
• Avoid all electrical dangers. Pay attention to the risks of electric shock or arc flash

hazards.

• Always bear in mind the risk of drowning, electrical accidents, and burn injuries.

Safety equipment

Use safety equipment according to the company regulations. Use this safety equipment
within the work area:

• Hard hat
• Safety goggles, preferably with side shields
• Protective shoes
• Protective gloves
• Gas mask
• Hearing protection
• First-aid kit
• Safety devices

NOTICE:

Never operate a unit unless safety devices are installed. Also see specific information
about safety devices in other chapters of this manual.

Electrical connections

Electrical connections must be made by certified electricians in compliance with all
international, national, state, and local regulations. For more information about
requirements, see sections dealing specifically with electrical connections.

1 Introduction and Safety

4

Series e-80SC INSTRUCTION MANUAL

«
...
4
5
6
7
8
...
»

Summary of Contents for e-80SC Series

































Reviews:

No comments

Related manuals for e-80SC Series

Brand: Jandy Pages: 96

Brand: Bacharach Pages: 12

Brand: Davey Pages: 4

Brand: TradeQuip Pages: 8

Nano-Flow 2,600

Brand: Cobalt Digital Inc Pages: 2

Brand: Barracuda PUMPS Pages: 4

Brand: Pentair Pages: 16

DSE-5 THRU DSE-120

Brand: A.O. Smith Pages: 24

Brand: clage Pages: 148

Brand: deconta Pages: 12

Brand: Trotec Pages: 18

Brand: American Hometec Pages: 51

Brand: Gorenje Pages: 40

Brand: BEKA Pages: 80

Brand: Ochsner Pages: 56

Brand: salmson Pages: 25

Water Heater 520 Direct Vent Indoor

Brand: A.O. Smith Pages: 97

Evacuated Tube Solar Water Heater

Brand: Sunshine Solar Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands