PROBLEM
POSSIBLE CAUSE
SOLUTION
Unit not on,
“ON/OFF/TEST” button
Press the “ON/OFF/TEST”
LED not lit
not pushed or pushed less
button for more than
than 2 seconds
2 seconds
Battery voltage is too low
Recharge the Unit
at least 8 hours
UPS fault
Contact service
personnel
Unit always on
Power cord loose
Re-plug the power cord
battery mode
AC breaker is burned
Replace or
out or tripped
reset the breaker
AC utility voltage is too high
Normal condition
or too low, or there is a
blackout
Backup time
Battery not fully charged
Recharge the Unit
too short
at least 8 hours
The Unit is overloaded
Remove some
unnecessary loads
Charger fault or other reason
Replace battery; contact
www.belkin.com
The Unit
Overload
Remove the
continuously
non-critical loads
beeps
Red LED lit
Battery failure
Replace battery; contact
www.belkin.com
F6B900-UNV, F6C900-UNV,
Battery Backup with Surge Protection User Manual
F6C1100-UNV, F6C1200-UNV
F6C550-AVR, F6C750-AVR, F6B750-AVR,
Battery Backup with Surge Protection User Manual
F6C900-UNV, F6C1100-UNV, F6C1200-UNV
Troubleshooting
Serial or USB Communication Port
Installation Optional
To fully utilize the Belkin Automatic Power Management Software, you will need to
connect the Unit to your computer.
The communication port will provide the following features:
1.
Monitoring charger status
2.
Monitoring Unit status
3.
Monitoring battery status and condition
4.
Monitoring the utility status
5.
Use the “ON/OFF/TEST” power switch function to schedule the
Unit for power-saving
You may connect the Unit to your computer by choosing either the serial or USB
ports.
NOTE: Choose one port only. Do not connect your computer through both
ports.
Install Belkin APM Software
a) System requirements
•
128 MB RAM of memory at least (256MB is recommended)
•
256 colors and 800 * 600 resolution or above display is recommended
•
160 MB of disk space or above
•
An available communication port (RS-232 Serial Port or USB port) is needed
while connecting to UPS with a special connecting cable.
•
For Mac OS X, Linux or Unix operating system, the user must have the access
authority as the super user
•
TCP/IP protocol must be installed to support network management
•
The user needs to have the access authority as the administrator
b) Platforms supported by Belkin APM Software.
The following operating system (OS) is arranged by the alphabetical order:
•
AIX 4.3.3, 5.1, 5.2
•
Compaq Tru64 Alpha
•
FreeBSD x86
•
HP-UX 11.x, 11i.x
•
Linux
•
Mac PPC OSX
•
SCO UnixWare 7.1.1, 7.1.3, SCO Unix 8.0, and SCO OpenServer 5.0.6, 5.0.7
•
SGI Irix 6.5.x
•
Solaris / Sparc 2.6, 7, 8, 9 , and Solaris / Intel 2.6, 7, 8, 9
•
Windows XP / 2003 / 2000 / ME / 98 / NT 4.0 (SP6).
c)
Belkin Automatic Power Management Software Installation Steps
.
For Windows platform
•
Run setup.exe in the \Windows\Disk1\InstData\VM\ directory of your CD to
start the installation program.
•
Read the information provided, then click Next.
•
Review the installation options that you have selected. If the options are
correct, then click “Install” to begin the installation.
•
When the installation program is completed, click Done.
For Mac OS X platform
•
Run setup.app in the \MacOXS\Disk1\InstData\ directory of your CD to start
the installation program.
•
Read the information provided, then click Next.
•
Review the installation options that you have selected. If the options are
correct, then click “Install” to begin the installation.
•
When the installation program is completed, click Done.
For Other Platforms
•
This CD provides two installation modes: GUI mode and Console mode. Enter
the directory according the system and run setup.bin or setup_console.
bin to start the installation program. Note: For UnixWare, Irix and Tru64
platform, make sure JRE1.3.1 has been install in your system, then enter the
/GenericUnix directory and run setup.bin or setup_console.bin to start the
setup.
•
Read the information provided, then click Next.
•
Review the installation options that you have selected. If the options are
correct, then click Install to begin the installation.
•
When the installation program is completed, click Done.
Reboot the system.
The install program set the Belkin Power Management Software Running
Environment Variables in /etc/profile, reboot the system to make it valid.
Uninstall Belkin APM Software
Note: Before uninstall Belkin PMS, all Belkin PMS program must be stopped first.
Otherwise the uninstalling cannot be run completely.
Windows operating system
1. There are two ways of uninstalling Belkin PMS:
(a) Click directly on the Uninstall Belkin Automatic Power Management Software
from the Start menu >Programs > Belkin Automatic Power Management
Software.
(b) Use the Add / Remove Program under Control, and select Change or Remove
Programs from the left. Select Belkin Automatic Power Management Software,
and click the Change / remove button.
2. The Uninstall Program will pop up a prompt, and click Uninstall to start the
uninstalling.
To exit the uninstallation, click Cancel.
Mac OS X system
open the Terminal from Application > Utilities> Terminal, enter the installation
directory (/opt/upspilot by default) and ececute the command: sudo ./Uninatall
Enter the system account password when it prompts. The installation will be carried
out with administrator privilege and can completely uninstall all the files.
If you just execute the ./Uninstall command , the installation may not has the
permission to uninstall all the files.
Information
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
To assure continued compliance, use only shielded interface cables when
connecting to computer or peripheral devices. Any changes or modifications
not expressly approved by the party responsible for compliance could void
the user’s authority to operate this equipment.
Belkin Corporation User License Agreement
Belkin Corporation (“Belkin”) thanks you for choosing one of our products.
This User License Agreement (“Agreement”) contains the terms and
conditions under which limited use of the product is licensed to you.
PLEASE READ THIS NOTICE CAREFULLY. DO NOT USE THE SOFTWARE
OR PRODUCT UNTIL YOU HAVE READ AND AGREED TO THIS
AGREEMENT. IF YOU USE THE SOFTWARE AND PRODUCT, YOU
ARE AGREEING TO THE TERMS AND CONDITIONS SET OUT IN THIS
AGREEMENT. IF YOU DO NOT ACCEPT THESE TERMS AND CONDITIONS,
YOU MUST RETURN THE UNOPENED PRODUCT WITH THE DISKS INSIDE
TO THE PARTY FROM WHOM YOU RECEIVED IT.
SCOPE OF USE:
In this Agreement, software means all
machine-readable software programs and associated files in this package,
all modified versions of and upgrades or improvements to such programs
and all copies of such programs and files. You, a single user opening this
envelope, may use the software on a single central processing unit. You may
not rent it, loan it out, or lease it, nor use it on a multiuser system.
LICENSE:
You have the non-exclusive right to use the software. You are not
permitted to copy, modify or transfer the software or documentation. You
may not compile, disassemble or otherwise reverse engineer, breakdown,
analyze or modify the software.
USE AND RESTRICTIONS:
You are permitted to make backup copies of
all the software disks for archival purposes only. You must reproduce the
proprietary notice set forth on the disks and affix them to all backup copies.
You are not permitted to use these programs in connection with a computer
service, or to use the backup copies other than as a replacement for the
original copy.
TERM:
This license is effective upon acceptance by opening this envelope
or in any other way using the enclosed software, which will constitute your
acceptance of, and agreement to, this Agreement, and is effective until
terminated. The limited license in this Agreement will be automatically
terminated if you fail to comply with any of the Terms and conditions in
this Agreement. You agree that upon such termination you will immediately
destroy all programs and documentation, including all copies made or
obtained by you.
SOFTWARE, PROGRAM, DOCUMENTATION, AND ANY RELATED
INFORMATION, GOODS OR SERVICES ARE PROVIDED WITH NO
WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER. BELKIN
HEREBY DISCLAIMS ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
The entire risk of the use, results and performance of the software, program
and documentation is borne by you. Should any or all of the product, software,
program, documentation, or related information, goods or services be defective,
misused, unsuitable or cause or give rise to any harm or liability whatsoever, you,
not Belkin or its associates, dealers or agents, assume the entire liability, cost of
repair, correction or any payment or other remedy whatsoever. Furthermore,
no warranty or guarantee is made regarding the use or results of the product,
software, program, documentation, or any related information, goods or services in
terms of correctness, accuracy, reliability, timeliness or otherwise. You use and rely
on the program at your own risk. The following is the only and exclusive warranty
and remedy of any kind: Belkin does warrant that the program disks are free from
physical defects in materials and workmanship under normal use for a period of
one (1) year from the date of purchase, as evidenced by a copy of the sales receipt.
Return the defective disk or documentation with your receipt directly to Belkin for
a replacement.
DISCLAIMER:
Belkin or its associates will in no event be liable (i) in any amount for
lost profits or special, incidental, punitive or consequential damages, or (ii) for any
claim or damage of any nature, or under any theory, whatsoever, in any amount in
excess of the purchase price you paid for the product. The warranties and remedies
here set forth are exclusive, and in lieu of all others oral or written, expressed
or implied. Some jurisdictions do not allow exclusion or limitation of implied
warranties or of liability for incidental damages, so the foregoing limitations or
exclusion may not apply to you. This warranty gives you specific legal rights, which
vary from jurisdiction to jurisdiction.
HOWEVER, YOU WAIVE SUCH RIGHTS, EXCEPT AS EXPRESSLY
PROVIDED UNDER THE TERMS AND CONDITIONS OF THIS AGREEMENT,
TO THE MAXIMUM EXTENT ALLOWED BY LAW.
The license is governed by the laws prevailing in the State of New York,
without regard to its conflicts of laws principles.
ACKNOWLEDGMENT:
By opening the package on which this Agreement is printed, or through
which it is visible, you acknowledge that you have read this Agreement,
understand it, and agree that this Agreement is the complete and exclusive
statement of agreement between yourself and Belkin and supersedes any
prior agreements, oral or written, and any other communications relating to
the subject matter of this Agreement.
SEVERABILITY:
Any term or provision of this Agreement or any application thereof, which may be
prohibited or unenforceable by law in a particular jurisdiction, shall be interpreted
and enforced to the maximum extent allowed in such jurisdiction (which the
parties acknowledge could mean severing the provision from this Agreement or,
if allowed, enforcing it in a narrower form), without affecting the remainder of this
Agreement, or any other application of such term or provision in such jurisdiction,
or application of such term or provision in
any jurisdiction.
Battery Name
Recycling Inside the USA
Outside the USA Recycling
BB Battery
(800) 278-8599
N/A
CSB Battery
(800) 738-7372
1 (817) 244-4415
VISION Battery
(604) 730-2877
N/A
Best Battery
(888) 841-5179
N/A
Safety Information
Caution
l
Internal battery voltage is 12V DC.
l
The Unit is intended for installation in a controlled environment
(temperature controlled, indoor area free of conductive contaminants).
l
All batteries used are sealed lead batteries. Batteries must be recycled.
Recycling
Your Unit contains a non-spillable sealed lead battery. On the battery, you
will find the battery name. Please reference the chart below for recycling
information.
Linux and UnixWare system
Open the Terminal, enter the /opt/upspilot in the address bar and execute
command: ./Uninstall.
Belkin Tech Support
US: 800-223-5546, ext. 2263
310-898-1100, ext. 2263
Europe: 00 800 223 55 460
Australia: 1800 235 546
New Zealand: 0800 235 546
Belkin Corporation
501 West Walnut Street
Compton, CA 90220-5221, USA
310-898-1100
310-898-1111 fax
Belkin Ltd.
Express Business Park, Shipton Way
Rushden, NN10 6GL, United Kingdom
+44 (0) 1933 35 2000
+44 (0) 1933 31 2000 fax
Belkin B.V.
Boeing Avenue 333
1119 PH Schiphol-Rijk, The Netherlands
+31 (0) 20 654 7300
+31 (0) 20 654 7349 fax
Belkin Ltd.
7 Bowen Crescent, West Gosford
NSW 2250, Australia
+61 (0) 2 4372 8600
+61 (0) 2 4372 8603 fax
© 2005 Belkin Corporation.
All rights reserved. All trade names are
registered trademarks of respective
manufacturers listed.
614-07166-00
Contact Belkin
