trOubleShOOtiNG
My device does not charge when
connected to the Conserve Valet.
Check that your Conserve Valet is securely
plugged into a power socket. Next you’ll want
to make sure that any device attached to
your Conserve Valet is securely connected
at both ends. Ensure that the start button
has been depressed and that the Conserve
Valet’s LED is green. If your device does not
begin to charge, disconnect the Conserve
Valet and your device and reconnect them
as described in the Quick Setup Guide.
NOte:
The Conserve Valet has been
designed with in-line signal resistors to work
with as many devices as possible. However,
the Conserve Valet’s configuration might
not be compatible with your device if it does
not charge when securely connected to the
Conserve Valet. Check with a local or online
retailer, or with your device manufacturer
for a compatible USB data connector
cord that has built-in signal resistors to
enable the charging of your device
after connecting devices to the Conserve
Valet and during operation, the led light
goes out and my electronics appear
not to be charging. additionally, when i
plug in my powered-down devices and
press
the start button, the lED turns
on, and then turns off and stays off.
Check all the cables on the Conserve Valet
and make sure they are connected securely.
Each port on the Conserve Valet is rated to
supply 500mA. However, some new devices
require more current than 500mA. Devices
with large color screens, such as smart
phones, often require more than 500mA.
The Conserve Valet has been designed with
additional charging capacity to accommodate
the majority of these types of devices. If your
connected device still does not begin to
charge, it is possible that the Conserve Valet
has reached its maximum charging capacity.
Try removing each attached device one by
one, pressing the start button after each
device is disconnected until the Conserve
Valet turns on (LED will illuminate green). It is
recommended you only charge two devices
with large color screens at the same time
i disconnected all my devices, but
the Conserve Valet stays on.
The Conserve Valet will detect when all
devices have been removed and will power
down automatically after approximately
two minutes.
NOte:
This product’s USB sockets cannot
be used as USB hubs and do not transmit
data. The powered USB sockets on this unit
are intended solely for charging devices
that can be charged via USB interface.
Specifications
.
Power Input: 100–240V~, 50/60Hz 0.5A
.
Power Output: +5V/500mA x 4 USB 2.0 port
Safety information
. important:
Use indoors in a dry location.
NOte:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna.
•
. Increase the separation between the equipment and receiver.
•
. Connect the equipment into an socket on a circuit
•
different from that which the receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
•
Belkin International, Inc., is not responsible for any interference caused
by unauthorized modifications to this equipment. Such modifications
could void the user’s authority to operate this equipment.
Ce Statement
Note
: This product complies with the essential requirements of the
European Union R&TTE Directive 1999/5/EC, the Low Voltage
Directive 2006/95/EC, and the EMC Directive 2004/108/EC. A
copy of the European Union CE marking "Declaration of Conformity"
may be obtained at the website: www.Belkin.Com/DOC
6
