BELINEA Belinea 2025 S1W User Manual Download Page 8

 Belinea 2025 S1W - Operating Instructions - 

7

ENGLISH

TROUBLESHOOTING

Blank Screen

Power indicator is off

Make sure the power cable is connected properly (see section “Connecting”).

-  Make sure that the monitor was turned on using the power switch (see section “Startup”).

Power indicator lights orange 

-  Perhaps a power saving mode is active? Press any key on your keyboard or move the mouse.

Power indicator lights green

-  A screen saver may have activated automatically after a certain period of inactivity. Press any key on your keyboard 

or move the mouse.

“No Signal!” message

-  Is the signal cable connected to the monitor and the PC’s graphics port (see section “Connecting”)?

-  Is the PC turned on (see your PC’s documentation)?

Display Problems

Image is displaced to the left/right or to the top/bottom

If the image appears normal but off-center, you can adjust it using the OSD functions. For further information, see 

chapter “Basic Setup”, section “Automatic Image Adjustment” or chapter “OSD Menu Functions”, section “

Image 

Control

”. 

Image flickers or is shaky

-  Perhaps setup file  chosen  for the monitor  is incorrect. For information on monitor  setup under Windows

®

  9x/

ME/2000/NT/XP 

consult the “Configuration” section.

Image is blurred

-  Check brightness and contrast settings (see chapter “

OSD Menu Functions”, section “

Brightness/Contrast

”).

Check the sharpness setting (see chapter “OSD Menu Functions”, section “Sharpness”).

Color problems

-  If the colors are off (e.g., white is not really displayed as white etc.), you should adjust the color temperature (see 

chapter “OSD Menu Functions”, section “Color”).

LCD panel

 

20.1 inch wide diagonal size (51.05 cm visible

), low radiation according to TCO 

'

03, 

certified to ISO 13406-2, pixel fault class II, TN + Film panel technology 

Contrast ratio 

 

1000:1 (typical) / 1100:1 (max.)

Viewing angle

 

(Contrast ratio 

≥ 10:1) 

horizontal 160°, vertical 160°

 (typical)                

(Contrast ratio 

≥ 5:1) 

horizontal 170°, vertical 170°

 (typical)

Response time

 

5 ms (typical)

Brightness

 

300 cd/m

2

 

(typical) / 320 cd/m

2

 

(max.)

Input signal

 

Video: analog (15-pin mini D-Sub)

Display colors

 

16.7 mill. colors 

Synchronization

 

30–81 kHz horizontal, 56–75 Hz vertical

Video band width

 

135 MHz (pixel rate)

Ergonomic resolution 

1680 × 1050 (60 Hz)

Audio 

Amplifier: 1 W at 8 Ohms 

 

Loudspeaker: 1 W continuous load, 1.5 W peak power

Power connection

 

100–240 V AC, 50–60 Hz

Power consumption

 

ON status: max. 45 W; color of the status LED: green

 

SLEEP status: < 2 W; color of the status LED: orange

 

Power saving functions EPA certified 

Dimensions/weight

 

Width: 473 mm, height: 394 mm, depth: 178 mm; 5.3 kg (net)

Operating environment

 

Operation: 0 to +40 °C, humidity: 20–80% (non-condensing)

 

Storage: -20 to +60 °C, humidity: 8–95% (non-condensing)

TECHNICAL SPECIFICATIONS

Summary of Contents for Belinea 2025 S1W













Reviews: