background image

DO NOT OPERATE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THE INSTRUCTIONS

IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY

1.  Never use the Booster Heat when solvent is in the machine.
2.  Never attempt to heat solvent above 130 °F.
3.  Always use a nonfl ammable solvent with a fl ash point of 140 °F or higher.

4.  The recovery bucket should be emptied each time the holding tank is fi lled.
5.  Always make sure the fl oat travels freely up and down the rod after emptying the recovery bucket.
6.  Always vacuum out the stainless steel tank and solution lines when switching from a solvent to a  
 

 water based detergent, and vice versa (see Operating Instructions).

7.  Always use a drop cloth under the machine during operation.
8.  Vacuum any unused solution out of the solution tank and empty the recovery bucket after each job.
9.  Keep machine from rain and snow, extremes in temperatures, and store in a heated location.     
 

Use the machine indoors.  Do not use outdoors.

10. Do not run the pump dry.
11. Never operate a machine that is leaking or in need of a repair.
12. Always use a defoamer.  The vacuum shut-off will not activate properly if foam is in the recovery  
 

bucket.  Water damage to the vacuum motor or other components will void the warranty.

If you have any questions before you operate the machine, call your supplier for instruction

.

THE ULTIMATE

®

: PB111

EXTRACTOR

120V

INFORMATION 

OPERATING 

INSTRUCTIONS

12-2010

DO NOT SMOKE WHEN USING HYDROCARBON-BASED SOLVENTS 

Even solvents with a fl ash point above 140 °F can be ignited, especially as an aerosol 

from the wand.

56041876

Summary of Contents for ULTIMATE PB111









Reviews: