BELFORNO 32 Installation And Operating Instructions Manual Download Page 12

 

Commercial and Residential Wood Fired Ovens 

Installation and Operating Instructions 

© Belforno Inc. 2012-2015. All rights reserved. 

Version 1.8 

12 

LIMITED WARRANTY 

 
Belforno Inc, manufacturer of wood fired ovens, (herein referred to as Product) warrants its Product to be 
free from defects in materials and workmanship for a period of one (1) year from the date of shipment. 
 

QUALIFICATIONS TO THE WARRANTY 

The complete Product Warranty outlined above does not apply under the following circumstances: 

1.  The  Product  was  not  installed  in  accordance  with  Belforno  installation  instructions  and  local 

building codes. 

2.  The Product is subjected to normal use including  burning such natural  wood fired oven fuels as 

non-treated  wood.  Fuel  products  with  abnormal  burning  characteristics  including,  but  not  limited 
to,  fuel  such  as  driftwood,  coal  or  plywood  and  wood  products  using  a  binder,  may  burn  at 
excessive  temperatures  and  may  cause  damage  to  the  Product  or  may  cause  it  to  function 
improperly. Belforno does not warrant the Product when such fuels have been used. 

3.  This Warranty does not apply to normal wear and tear, or damage due to water penetration. 
4.  This  Warranty  does  not  apply  to  any  cracking  caused  by  over-firing  or  the  failure  to  follow  a 

proper curing schedule. 

5.  On parts that would be normally worn or replaced under normal conditions. 
6.  Normal cracking due to expansion and contraction stress relief in either the dome or floor blocks. 

 

LIMITATION ON LIABILITY 

It  is  expressly  agreed  and  understood  that 

Belforno’s  sole obligation  and  purchaser's exclusive remedy 

under  this  Warranty,  under  any  other  warranty,  expressed  or  implied,  otherwise,  shall  be  limited  to 
replacement,  repair,  or  refund,  as  specified  above,  and  such  liability  shall  not  include,  and  purchaser 
specifically  renounces  any  rights  to  recover,  special,  incidental,  consequential  or  other  damages  of  any 
kind whatsoever, including, but not limited to, injuries to persons or damage to property, loss of profits or 
anticipated profits, or loss of use of the product. 
 
In no event shall Belforno be responsible for any incidental or consequential damages caused by defects 
in its products, whether such damage occurs or is discovered before or after replacement or repair, and 
whether or not such damage is caused by 

Belforno’s negligence. Some states do not allow the exclusion 

or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to 
you.  The  duration  of  any  implied  warranty  with  respect  to  this  Product  is  limited  to  the  duration  of  the 
foregoing  warranty.  Some  states  do  not  allow  limitations  on  how  long  an  implied  warranty  lasts,  so  the 
above may not apply to you. 
 

INVESTIGATION OF CLAIMS AGAINST WARRANTY 

Belforno  reserves  the  right  to  investigate  any  and  all  claims  against  this  Warranty  and  to  decide  upon 
method of settlement. 
 

DEALERS HAVE NO AUTHORITY TO ALTER THIS WARRANTY 

Belforno’s  employees  and  dealers  have  no  authority  to  make  any  warranties  nor  to  authorize  any 
remedies in addition to or inconsistent with those stated above. 
 

HOW TO REGISTER A CLAIM AGAINST WARRANTY 

In order for any claim under this Warranty to be valid,  Belforno must be notified of the claimed defect by 
telephone or in writing to Belforno Inc, 230 Wonderwood Drive, Charlotte NC 28211-4012. Claims against 
this Warranty in writing should include the date of installation, and a description of the defect.  
 
 

Summary of Contents for 32















Reviews: