FMHD-1 Operator’s Manual
Page 38
FMHD-1
Wideband
This adjective refers to the frequency span of the pass-band for band-pass or low-pass signals. It suggests
the widest practical pass-band for a signal. For low-pass signals, it also implies the un-de-emphasized, or
“flat” version of the signal.
9
Software Setup and Unit Update Information
The
FMHD-1
may be connected to a computer using the
Belar
WizWin©
Software
, which can be downloaded
from our website at
www.belar.com
. Connections can be made using the RS-232 port or Ethernet jacks on the rear
panel. In addition to accessing the unit remotely, the
Belar
WizWin
Software
may also be used to update the
FMHD-1
firmware in the field.
Please check our website at
www.belar.com
for the latest software updates, as we are always improving our
products and adding features.
9.1
Connecting to the unit using the RJ-45 Network Jack
a.
Download and Install the latest version of
Belar
WizWin©
Software
from our website.
b.
If connecting to a network with a DHCP server in place (the
FMHD-1
is shipped with DHCP enabled)
connect the
FMHD-1
to your network, on the same subnet as the computer you loaded the
Belar
WizWin©
Software
, and power cycle the unit.
c.
If your network does not have a DHCP server, the
FMHD-1
will select an APIPA (Automatic Private IP
Address) address in the 169.254.xxx.xxx range with a 255.255.0.0 subnet. You can then use an isolated
(non DHCP) switch or a crossover cable to connect the
FMHD-1
to your computer. You must set the
computer IP to the same 169.254.xxx.xxx range with the 255.255.0.0 subnet. (Most computers set to DHCP
enabled will default to an APIPA address if no DHCP server is present when they are booted up).
d.
To obtain the Units IP address on the
FMHD-1
, activate the popup menu and select Settings, under
Settings select the Network: Status submenu to display the current network information. Make sure that the
FMHD-1
is power cycled after the RJ-45 cable has been connected to the unit.
e.
To set a Static IP address on the
FMHD-1
, activate the popup menu and select Settings, under Settings
select the Network: Configure submenu to enter the IP Address, subnet, and gateway. DHCP must be
disabled to set a static IP.
f.
Run the
Belar
WizWin
Software
and select “Connections” from the window. A pop-up dialog box will
appear, select “Connection #1” and click the “Configure” Button. Using the tabs in the Configuration
Dialog Box set the “Hardware Type” to “
FMHD-1
”, set the “Connection Type” to “Network-Ethernet”,
and under “Network” set the “IP Address” to the address displayed on the
FMHD-1
, then set the “PORT”
to “10001”, click the “Save” Button to finish. Finally, click the “Connect” Button and the unit will connect
and display a virtual front panel of the unit.
9.2
Connecting to the unit using the RS-232 Port
a.
Download and Install the latest version of
Belar
WizWin©
Software
from our website.
b.
Connect the unit to the computer using a 9-pin serial modem cable.
c.
Run the
Belar
WizWin
Software
and select “Connections” from the window. A pop-up dialog box will
appear, select “Connection #1” and click the “Configure” Button. Using the tabs in the Configuration
Dialog Box set the “Hardware Type” to “
FMHD-1
”, set the “Connection Type” to “RS-232”, under
“RS-232” set the “COM Port” to the COM Port being used on the computer, click the “Save” Button to
finish. Finally, click the “Connect” Button and the unit will connect and display a virtual front panel of the
unit.
Summary of Contents for FMHD-1
