8
If your supply cord type is 5-conductor type,
for 1-phase connection:
For single phase connection
- (BRW/BLA) Brown/Black = L (Phase)
- (BLU/GRE) Blue/Grey = N (Neutral)
- (GR/YE) Green/yellow wire = (E)
(Earthing)
If your supply cord type is 5-conductor type,
for 2-phase connection:
- (BRW) Brown = L1 (Phase)
- (BLA) Black = L2 (Phase)
- (BLU/GRE) Blue/Grey = N (Neutral)
- (GR/YE) Green/yellow wire = (E)
(Earthing)
If your supply cord type is 4-conductor type,
for 2-phase connection:
- (BRW) Brown = L1 (Phase)
- (BLA) Black = L2 (Phase)
- (BLU) Blue = N (Neutral)
- (GR/YE) Green/yellow wire = (E)
(Earthing)
If your supply cord type is 5-conductor type,
for 3-phase connection:
- (BRW) Brown = L1 (Phase)
- (BLA) Black = L2 (Phase)
- (GRE) Grey = L3 (Phase)
- (BLU) Blue = N (Neutral)
- (GR/YE) Green/yellow wire = (E)
(Earthing)
For the protection of the appliance
against burning:
•
Make sure that the product plug is
securely plugged into the outlet to avoid
arcing.
•
Do not use damaged cables or
extension cables.
•
Ensure liquid or moisture is not
accessible to the electrical connection
point.
Placement and securing of the
appliance (Figures 5-6-7-8)
•
After preparing the installation location
of the appliance, turn the cooker upside
down and place it on a flat surface.
•
Affix the sealing gasket supplied with
the appliance around the cooker so
that it shall be 1-2 mm inside the outer
edge of the glass as shown in Figure 5.
Ensure that no clearance is left between
both ends and between the glass and
gasket.
•
Screw and secure the installation
springs supplied with the appliance
by engaging them to their seat on
the lower housing of the cooker as
shown in Figure 6. (In some models,
these springs may be secured to the
appliance ex-factory.)
•
Turn the cooker again and align it with
the worktop and then place it on the
worktop. Cooker shall be placed on the
worktop thanks to the springs, and it
shall be easily secured.
•
Ensure that the cooker and the
worktop are parallel when you place
the cooker on the worktop. When it is
not in parallel, connect the additional
installation clamps supplied with the
appliance as shown in Figure 8. Figure
8 shows the possible installation
locations of the clamps. (The locations
where the clamps can be attached
may vary depending on the product
model. You can connect according to
the mounting holes on your product.)
Ensure the parallelism by attaching the
clamps to the appropriate locations.
The type and quantity of clamps
supplied with the product may vary
depending on the product model.
Placement and securing of the
appliance (Figures 9)
•
Figure 9 is for the models with
mounting springs and sealing gasket
attached to the product. For these
models, ignore the pictures 5-6-7-8.
For these models, consider the width
and depth measurements written in the
user manual as 10 mm more.
•
Align the hob with the worktop and
then place it on the worktop. Hob shall
be placed on the worktop thanks to the
springs, and it shall be easily secured.
•
Ensure that the hob and the worktop
are parallel when you place the hob on
the worktop.
Final inspection
•
After completing the installation, turn on
the mains supply.
•
Read the operation manual for the first
operation of the appliance.
•
Ensure that each cooking hob heats.
Removal of the appliance
•
Disconnect the mains supply of the
appliance.
•
If your appliance is secured with
additional clamps, remove the screws
of the clamps first.
