- 14 -
of the appliance.
- To prevent the danger of possible fires, at least every
2 months one must wash the anti-grease filters by hand
using non-abrasive neutral liquid detergents or in the
dishwasher at low temperatures and on short cycles.
- After a few washes, colour alterations may occur. This
does not give the right to claim their replacement.
• The active carbon filters
are used to purify the air that
is sent back into the room and its function is to mitigate
the unpleasant odours produced by cooking.
- The non-regenerable active carbon filters must be
replaced at least every 4 months. The saturation of the
active charcoal depends on the more or less prolonged
use of the appliance, on the type of kitchen and on the
frequency with which anti-grease filter is cleaned.
- Regenerable active charcoal filters must be washed
by hand, with non abrasive neutral detergents, or in the
dishwasher at a maximum temperature of 65°C (the wa-
shing cycle must be complete without dishware). Remove
excess water without damaging the filter, remove the
plastic parts, and let the mat dry in the oven for at least
15 minutes approximately at a maximum temperature of
100°C. To keep the regenerable charcoal filter functioning
efficient this operation must be repeated every 2 months.
These must be replaced at least every 3 years or when the
mat is damaged.
• Before remounting the anti-grease filters and the
regenerable active charcoal filters it is important
that they are completely dry.
• Clean the hood frequently, both internally and
externally, using a cloth dampened with denatured
alcohol or neutral liquid detergents that are non
abrasive.
•
The lighting .system is designed for use during cooking
and not for the prolonged general lighting of the room.
The prolonged use of the lighting system significantly
decreases the average duration of the bulbs.
•
If the appliance is equipped with courtesy lights it is pos-
sible to use them for general room lighting for a prolonged
amount of time.
• Attention:
the non compliance with the hood cleaning
warnings and with the replacement and cleaning of the
filters entails risk of fires. One therefore recommends
keeping to the suggested instructions.
• Replacing halogen light bulbs (Fig.7A):
To replace the halogen light bulbs
B
, remove the glass
pane
C
using a lever action on the relevant cracks. Replace the
bulbs with new ones of the same type.
Caution:
do not
touch the light bulb with bare hands.
• Replacing LED lamps (Fig.7B):
If the appliance version is with LED lamps, the intervention
of a specialised technician is necessary to replace them.
• Replacing the halogen/incandescent lamps
(Fig.8):
Only use lamps of the same type and Wattage installed
on the device.
• Commands luminous
(Fig.9)
the key symbols are
explained below:
A =
LIGHT
B =
OFF
C =
SPEED I
D =
SPEED II
E =
SPEED III
F =
AUTOMATIC STOP TIMER - 15 minutes
(*)
If your appliance has the
INTENSIVE
speed function,
from speed THREE, press key
E
for 2 seconds and it will
be activated for 10 minutes after which it will return to
the previously set speed. When the function is active the
LED flashes. To interrupt it before the 10 minutes have
elapsed, press key
E
again. Some models allow activating
this function even with speed one and two.
By pressing key
F
for two seconds (with the hood switched
off) the “
clean air
” function is activated. This function
switches the appliance on for ten minutes every hour at
the first speed. As soon as this function is activated the
motor starts up at the first speed for ten minutes. During
this time key
F
and key
C
must flash at the same time. After
ten minutes the motor switches off and the LED of key
F
remains switched on with a fixed light until the motor
starts up again at the first speed after fifty minutes and
keys
F
and
C
start to flash again for ten minutes and so
on. By pressing any key for the exclusion of the hood light
the hood will return immediately to its normal functioning
(e.g. if key
D
is pressed the “
clean air
” function is deac-
tivated and the motor moves to the 2nd speed straight
away. By pressing key
B
the function is deactivated).
(*)
The “
AUTOMATIC STOP TIMER
” delays stopping of
the hood, which will continue functioning for 15 minutes
at the operating speed set at the time this function is
activated.
• Anti-grease/active charcoal filters saturation:
- When the
A
key flashes with a
2 second
frequency the
anti-grease filters must be washed.
- When the
A
key flashes with a
0.5 second
frequency
the active carbon filters must be replaced or washed
depending on the type of filter.
Once the clean filter has been put back one must reset
the electronic memory by pressing the
A
key for approxi-
mately
5 seconds
until it stops flashing.
• Commands slider (
Fig.10)
the key symbols are ex-
plained below:
A =
Light switch
A1 =
Off key
A2 =
On key
B =
Gemma warning light key
C =
Speed control
C1 =
Off key
C2 =
FIRST SPEED key
C3 =
SECOND SPEED key
C4 =
THIRD SPEED key.
• Mechanical controls (Fig.11)
the symbols are as fol-
lows:
A =
LIGHT/ON-OFF key
B =
OFF/FIRST SPEED key
C =
SECOND SPEED key
D =
THIRD SPEED key.
If the hood is shut off at first, second or third speed, when
it is turned back on, it will start at the same speed it was
in when switched off.
• Commands mechanical (Fig.12
.A.B.C
)
the key sym-
bols are explained below:
A =
LIGHT
B =
OFF
C =
SPEED I
D =
SPEED II
E =
SPEED III
G =
MOTOR WORKING indicator.
THE MANUFACTURER DECLINES ALL RESPONSIBIL-
ITY FOR EVENTUAL DAMAGES CAUSED BY BREACH-
ING THE ABOVE WARNINGS.
Summary of Contents for CWB 6430 W
