Beko BEKOMAT 12i Original Installation And Operation Manual Download Page 70

Page: 70 / 76

14.2 Disposal of operational materials and components

Ensure the following prerequisites are met before disposal:

Preparatory tasks

The

BEKOMAT

has been decommissioned.

The

BEKOMAT

is disassembled.

The

BEKOMAT

is clean and free from all media residues.

Operating material / components

EU waste code

Adsorption materials, filter materials, cleaning wipes and protective clothing

- contaminated by oils or other hazardous substances

15 02 02

Adsorption materials, filter materials, cleaning wipes and protective clothing
- with the exception of those classified by 15 02 02

15 02 03

Packaging - paper and cardboard

15 01 01

Packaging - plastic material

15 01 02

Electric and electronic devices with the exception of those covered by
20 01 21, 20 01 23 and 20 01 35

20 01 36

BEKOMAT

12i / 12i CO / 12i CO PN63

Original installation and operation manual

70 | 76

Summary of Contents for BEKOMAT 12i













































































Search results

Summary of Contents for BEKOMAT 12i

Reviews:

Brands by name

Popular brands

Beko BEKOMAT 12i, Original Installation And Operation Manual

Search results

Summary of Contents for BEKOMAT 12i

Reviews:

Brands by name

Popular brands