Beko 9910, Manual, Page: 9 / 44

- 9 -
• Clean the fan and other surfaces of the cooker hood
regularly using a cloth moistened with denatured alcohol
or non abrasive liquid detergent.
• The illumination installation is designed for use during
cooking and not for prolonged general illumination of the
environment. Prolonged use of the illumination installation
notably reduces the duration of the bulb.
Please note:
If your appliance model is fitted with side panels (A),
for more thorough cleaning these can be removed by
pulling them in the direction indicated in fig. 12.
• Replacing halogen light bulbs (Fig. 13).
To replace the halogen light bulbs B , remove the glass
panel C using a lever action on the relevant cracks.
Replace the bulbs with new ones of the same type.
Caution: do not touch the light bulb with bare
hands.
COMMANDS: (Fig.17)
Push-button A
= on/off lights switch
Push-button B = on/off cooker hood switch. The
appliance switches on at speed level 1, If the cooker hood
is on depress the push-button for 2 sec. to switch off the
cooker hood. If the cooker hood is at speed level 1 it will
not be necessary to depress the push-button to switch the
cooker hood off. Decreases the motor speed.
Display C = indicates the motor speed level selected and
activates the timer.
Push-button D = switches on the cooker hood. Increases
the motor speed. Touching the key at 3rd speed, the
intensive function runs for 10’, then the appliance go
back to work at the original speed. During this function
the display blinks.
Key E = The Timer times the functions on activation for
15 minutes, after which they are switched off. The Timer
is deactivated by re-pressing
Key E
. When the Timer is
activated the decimal point must flash on the display.
The Timer cannot be activated if the intensive speed is
functioning.
The “ clean air ” function is activated by pressing key E for
2 seconds when the appliance is switched off.
This switches the motor on for 10 minutes every hour at
the first speed.
During functioning a rotary movement of the peripheral
segments must be visualised on the display. When this time
has passed the motor switches off and the fixed letter “
C ”
must be visualised on the display until the motor re-starts
after 50 minutes for another 10 minutes and so on.
Press any key apart from the light keys to return to normal
functioning. Press key
E to deactivate the function.
• Active carbon/grease filter saturation:
- When display item C flashes, at a speed where it
alternates with the letter F (e.g. 1 and F ), the grease filters
must be washed.
- When display item
C flashes, at a speed where it
alternates with the letter A (e.g. 1 and A ), the carbon filters
must be replaced.
After the clean filter has been positioned correctly, the
electronic memory must be reset by pressing button
A
for approximately 5 seconds , until the indication F or A
shown on the display
C
stops flashing.
• COMMANDS: (Fig.16) LUMINOUS the key symbols
are explained below:
A = LIGHT
B
= OFF
C = SPEED I
D = SPEED II
E = SPEED III
F
= AUTOMATIC STOP TIMER - 15 minutes (*)
• If your appliance does not have the INTENSIVE speed
function, press key E for two seconds and it will be
activated for 10 minutes after which it will return to the
previously set speed.
When the function is active the LED flashes. To interrupt it
before the 10 minutes have expired press key
E again.
• By pressing key F for two seconds (with the hood
switched off) the “ clean air ” function is activated. This
function switches the appliance on for ten minutes every
hour at the first speed. As soon as this function is activated
the motor starts up at the first speed for ten minutes, During
this time key
F and key C must flash at the same time.
After ten minutes the motor switches off and the LED of
key F remains switched on with a fixed light until the motor
starts up again at the first speed after fifty minutes and keys
F and C start to flash again for ten minutes and so on.
By pressing any key for the exclusion of the hood light the
hood will return immediately to its normal functioning (e.g.
if key D is pressed the “
clean air ” function is deactivated
and the motor moves to the 2nd speed straight away. By
pressing key
B the function is deactivated).
(*) The “
automatic stop timer
” delays stopping of the
hood, which will continue functioning for 15 minutes at the
operating speed set at the time this function is activated.
•
Active carbon/grease filter saturation:
- When button A flashes at a frequency of 2 seconds , the
grease filters must be cleaned.
- When button A flashes at a frequency of 0.5 seconds ,
the carbon filters must be replaced.
After the clean filter has been replaced, the electronic
memory must be reset by pressing button
A for
approximately 5 seconds , until the light on the button
stops flashing.
T H E M A N U F A C T U R E R D E C L I N E S A L L
RESPONSIBILITY FOR EVENTUAL DAMAGES
CAUSED BY BREACHING THE ABOVE WARNINGS.