manualshive.com logo in svg

BEKA BA538C, Manual, Page: 16 / 26

Share
Download
BEKA BA538C Manual Download Page 16

16

Step 11 Reset the grand total to zero

Before completing commissioning  the
grand total counter should be reset to
zero.  Select 'CLr. Gtot' from the main
menu and press

 P

 which will cause the

instrument to display 'Clr. no'.   Toggle
this to 'CLr. YES' using the 

Up

 or

Down

 push-buttons and press 

P

 which

will result in a '0000' prompt.  Using the

Up

, and

 Down

 buttons and the

  P

button to move to the next digit,
confirm the request by entering the
password 'SurE'. Note: S is entered as
5.    Pressing

  E

 will then reset the

grand total counter to zero and return
the instrument to the 'CLr. Gtot' prompt
in the main menu.

Step 12 Define the security code

Defining a security code prevents
unauthorised access to the programme
functions.   Select 'COdE' from the
main menu and press 

P

 which will

reveal the existing security code.
Using the 

Up

 and 

Down

 buttons enter

the new code 1209 digit by digit.  The

P

 button will transfer control between

digits. When the new code has been
entered, press 

E

 to return to the main

programme menu.

Step 13 Return to the display mode

Following completion of programming
and calibration, return the BA538C to
the operating mode by pressing 

E

.  All

the  programming functions will now be
stored in permanent memory and will
be protected from accidental or
unauthorised adjustment by the
security code.

Summary of Contents for BA538C



























Reviews:

No comments