BEKA BA384E, Manual

Page: 2 / 68

2
1. DESCRIPTION
2. OPERATION
2.1 Initialisation
2.2 Controls
2.3 Displays
2.3.1 Display over-range
3. INTRINSIC SAFETY CERTIFICATION
3.1 ATEX gas certification
3.2 Zones, gas groups & T rating
3.3 Special conditions for safe use
3.4 Power
supply
3.5 Pulse input terminals
3.5.1 Flowmeters that do not require
energising.
3.5.2 Flowmeters that do require
energising.
3.6 Remote reset terminals
3.7 Certification label information
4. SYSTEM DESIGN FOR HAZARDOUS AREAS
4.1 Use with Zener barriers
4.1.1 Power supply
4,1,2 Pulse inputs
4.1.3 Switch contact input
4.1.4 Open collector input
4.1.5 2-wire proximity detector input
4.1.6 Magnetic
pick-off input
4.1.7 Voltage pulse input
4.1.8 Remote reset
4.2 Use with galvanic isolators
4.2.1 Power supply
4.2.2 Pulse inputs
4.2.3 Switch contact input
4.2.4 Open collector input
4.2.5 2-wire proximity detector input
4.2.6 Magnetic pick-off input
4.2.7 Voltage pulse input
4.2.8 Remote reset
5. INSTALLATION
5.1 Location
5.2 Installation procedure
5.3 EMC
5.4
Units of measurement and tag marking on
scale card.
6. CONFIGURATION AND CALIBRATION
6.1 Calibration structure
6.2 Accessing configuration functions
6.3 Summary of configuration functions
6.4
Rate totaliser function:
function
6.5 Input:
input
6.6 Input type:
inp.type
6.7 Debounce:
debounce
6.8 Display update interval:
update
6.9 Count:
count
6.10 Upper display:
di5p-1
6.11 Lower display:
di5p-2
6.12 Position of decimal points:
dp
6.13 Flowmeter K-factor:
factor-a
6.14 Total scale factor:
5cale.t-a
6.15 Rate scale factor:
5cale.r-a
6.16 Timebase:
t-ba5e
6.17 Display filter:
filter-a
6.18 Clip-off:
clp.off-a
6.19 Local reset:
loc clr
6.20 Local total reset:
clt tot
6.21 Local grand total reset:
clr gtot
6.22 External reset:
e clr
6.23 Grand total reset from configuration menu:
clr-gtot
6.24 Define security code:
code
6.25 Reset to factory defaults:
r5et def
7. LINEARISERS
7.1 Flowmeter specification
7.2 Summary of lineariser configuration
functions.
7.3 Copy A lineariser to b lineariser:
copy a2b
7.4 Add a segment:
add
7.5 Remove a segment:
del
7.6 Input frequency:
pul5e fr
7.7 Flowmeter K-factors:
l-factor
7.8 Lineariser error messages
7.9 Lineariser factory defaults
8. Pulse Output
8.1 Intrinsic safety
8.2 System design
8.3 Configuration
8.4 Access pulse output sub-menu
8.5 Enable pulse output:
enbl
8.6 Source of output pulse:
5ource
8.7 Divide output pulse frequency:
divide
8.8 Define output pulse width:
duration
8.9 Stored pulses
The BA384G and BA384E are CE marked to show compliance with European Explosive Atmospheres
Directive 2014/34/EU and European EMC Directive 2014/30/EU.
CONTENTS