manualshive.com logo in svg

BEKA Advisor A90-SS, Manual

Share
Download
BEKA Advisor A90-SS Manual Download Page 22

Fig 12  Typical alarm application

(Shown without recommended screen cables)

7.3.2  Configuration and adjustment

When optional alarms are fitted the A90-SS panel
meter configuration menu is extended as shown in
Fig  11.     For  simplicity  Fig  11  only  shows  the
additional functions for alarm 1, but alarm 2 has
identical functions.

The following table summarises each of the alarm
configuration  functions  and  includes  a  cross
reference to more detailed information.   Again only
the functions on alarm 1 are listed, but alarm 2 has
identical facilities.

    

Display

       Summary of function

   

 

EnbL

Alarm enable

Enables or disables the alarm without
changing the alarm parameters.
See section  7.3.3

5P1

Setpoint adjustment

Adjusts the alarm setpoint.  The alarm
is   activated   when   the   meter   display
equals the setpoint.
See section 7.3.4

    

Display

       Summary of function

   

Hi.

  

Lo

Alarm function

Defines the alarm function as High or
Low.
See section 7.3.5

nd

  

.

  

nE

Alarm  relay  energised  or
de-energised in non alarm condition.

Determines whether the alarm relay is
energised  or  de-energised  in  the
non alarm condition.
See section 7.3.6

H5tr

Hysteresis

Adjusts the alarm hysteresis.
See section 7.3.7

dELA

Alarm delay

Introduces  adjustable  delay  between
the display equalling  the  setpoint  and
the alarm being activated. 
See section 7.3.8

5iL

Alarm silence time

Defines the time that the alarm output
remains  in  the  non-alarm  condition
following acceptance of an alarm.
See section 7.3.9

FLA5H

Flash display when alarm occurs

When enabled, alternates the A90-SS
meter  display  between  the  process
value and the alarm reference, 

ALr1

 or

ALr2

,  when  an  alarm  output  is

activated. 
See section 7.3.10

latch

Latch alarm output

When enabled, maintains alarm output
until the alarm is manually cleared by
operating the 

(

 button. 

See section 7.3.11

Color

Display colour in Alarm condition

Defines the colour of the A90-SS panel
meter display when an alarm occurs. 
See section 7.3.12

AC5P

Access to setpoint in display mode

Sub-menu which enables direct access
to the alarm setpoints from the A90-SS
meter  display  mode,  and  defines  a
separate security code.
See section 7.3.13

22

Summary of Contents for Advisor A90-SS





























Reviews:

No comments

Brands by name

Popular brands

Load more brands