BEINAT SG580 Installation And User Manual Download Page 7

Page  7

The  installation  of  the  SGM595  probe,  its  ordinary  and
extraordinary  maintenance,  and  its  out  of  service  removal
at  the  end  of  the  functional  life  guaranteed  by  the
manufacturer,  must  be  carried  out  by  authorized  or
specialized  personnel.

The  general  test  should  be  performed  by  issuing  gas  from
a  pre-calibrated  aerosol  within  the  percentages  illustrated
on  the  side.

Important: 

This  test  must  be  carried  out  at  least  once  a

year.

Gas  imput  Test

WARNING! Actions to be taken in case of alarm

Gas
1) P
ut out all free flames.
2) Close the main gas tap or the LPG cylinder tap.
3) Do not turn any lights on or off; do not turn on any electrical device or appliance.
4) Open windows and doors in order to increase ventilation.
If the alarm stops, its cause must be found and the relevant consequent measures taken.
If the alarm continues and the cause of gas presence cannot be found or removed, abandon the building and call
the emergency services when outside (fire department, distributors, etc.)

IMPORTANT:  The  operation  test  should  not  be  carried  out  with  the  gas  tap  as  this  does  not  guarantee  a  sufficient
concentration  to  activate  the  general  alarm.

Warning !!

If you have the following symptoms: vomiting, sleepiness, or else, go to the closest first aid station
and inform the operators that you could have been poisoned by Carbon Monoxide

or by an excess

or  deficiency  of  oxygen

N O T E S

Gas

SG580  Test

Methane

At 20% of L.E.L. ±2%

LPG

At 20% of L.E.L. ±2%

Hydrogen

At 20% of L.E.L. ±2%

Summary of Contents for SG580









Reviews: