4
Chemical Resistance
4.1
Metal Casing
The frame and casing material is powder-coated aluminum. This powder paint
withstands exposure to the following chemicals without visible change:
Acetic acid 10%
Phosphoric acid 4%
Citric acid 10%
Phosphoric acid 10%
Diesel
Sea water
Distilled water
Sodium chloride 2%
Edible oil
Sodium chloride 20%
Fuel oil
Sulphuric acid 20%
Hydrogen peroxide 3%
Tap water
The powder paint shows limited resistance to the following chemicals at room
temperature:
Butanol
Nitric acid 3%
Hydrochloric acid 5%
Nitric acid 10%
Isopropyl alcohol
Phosphoric acid 43%
Na-hypochlorite 10%
Turpentine
Note:
If exposure to any of the above chemicals is demanded, it is recommended to
fi
rst test the chemical on an “invisible” spot of the metal casing.
The powder paint shows little or no resistance to the following chemicals at room
temperature:
Acetic acid, conc.
Methyl-ethyl ketone
Toluene
Acetone
Nitric acid 30%
Trichlorethylene
Ammonia 5%
Phenol
Xylene
Ammonia, conc.
Sodium hydroxide 5%
97 octan unleaded
petrol
Ethyl acetate
Sodium hydroxide 30%
98 octan leaded petrol
4.2
Touch Screen and Overlay
4.2.1
Auto
fl
ex EBA 180L
Autoflex EBA 180L covers the overlay surrounding the touch screen.
Solvent Resistance
Autoflex EBA 180L withstands exposure of more than 24 hours duration under
DIN 42 115 Part 2 to the following chemicals without visible change:
Acetonitrile
Diesel Downey /
Lenor
1
Phosphoric acid (<30%)
Ajax / Vim in solution
Ethanol
Potassium
ferricyanide
Alkalicarbonate
solution
1
Glycerine
Potassium hydroxide
(<30%)
Ammonia (<40%)
1
Glycol
Pure Turpentine
Acetic acid (<50%)
Gumption
1
SBP 60/95
1
Ariel powder in
solution
1
Hydrochloric acid
(<36%)
Sulfuric acid (<10%)
Bleach
1
Linseed oil
Tomato ketchup
Castor oil
Methanol
Trichloroacetic acid
(<50%)
Caustic soda (<40%)
1
Nitric acid (<10%)
White Spirit
Cutting oil
Paraf
fi
n oil
Windex
1
Cyclohexanol
Persil powder in
solution
1
Wisk
Diacetone alcohol
Petroleum spirit
1
-
1
Extremely faint glossing of the texture was noted.
Autoflex EBA 180L withstands DIN 42 115 Part 2 exposure of up to 1 hour
duration to glacial acetic acid without visible change.
Autoflex EBA 180L is not resistant to high pressure steam at over 100 °C or the
following chemicals:
Concentrated mineral acids
Benzyl alcohol
Concentrated caustic solution
Methylene chloride
4.2.2
Touch Screen Surface
The touch screen surface on the operator panel withstands exposure to the following
solvents without visible change:
Solvents
Time
Acetone
10 minutes
Isopropanol
10 minutes
Toluene
5 hours
4.2.3
Auto
fl
ex EB
It is recommended to use the Autoflex EB touch display protection film, that can be
ordered from Beijer Electronics.
Outdoor Use
In common with all polyester based films Autotex EB is not suitable for use in
conditions of long term exposure to direct sunlight.
5
Operator Panel Drawings
5.1
Communication Ports
Serial port, 9-pin female
Serial port, 9-pin female
Pin
COM1
COM2
COM3
COM4
1
RS422 TX+
/ RS485
TX+/RX+
RS422 TX+
/ RS485
TX+/RX+
2
RS232 RX
RS232 RX
3
RS232 TX
RS232 TX
4
RS422 RX+
RS422 RX+
5
GND
GND
GND
GND
6
RS422 TX-
/ RS485
TX-/RX-
RS422 TX-
/ RS485
TX-/RX-
7
RS232 RTS
RS422 RTS+
8
RS232 CTS
RS422 RTS-
9
RS422 RX-
RS422 RX-
Note:
Drawing for external cable CAB109 (drawing # Z7100-029E) is available on the
web site:
www.beijerelectronics.com
5.2
T10A Outline
280
228
max 8 mm
material thickness
7
44
262
9
9
209
9
9
USB host
SD memory
card slot
Expansion port
COM3 RS232 /
COM4 RS422/RS485
COM1 RS232 /
COM2 RS422/RS485
Ethernet
24 V DC
Note:
A Step CAD
fi
le is available on the web site
www.beijerelectronics.com
Order no: MAEN017C
Copyright © 2012-04 Beijer Electronics AB. All rights reserved.
The information in this document is subject to change without notice and is
provided as available at the time of printing. Beijer Electronics AB, including
all its group companies, reserves the right to change any information without
updating this publication. Beijer Electronics AB, including all its group
companies, assumes no responsibility for any errors that may appear in this
document. Read the entire installation manual prior to installing and using
this equipment. Only qualified personnel may install, operate or repair this
equipment. Beijer Electronics AB, including all its group companies, are
not responsible for modified, altered or renovated equipment. Because the
equipment has a wide range of applications, users must acquire the appropriate
knowledge to use the equipment properly in their specific applications. Persons
responsible for the application and the equipment must themselves ensure that
each application is in compliance with all relevant requirements, standards and
legislation in respect to configuration and safety. Only parts and accessories
manufactured according to specifications set by Beijer Electronics AB, including
all its group companies, may be used.
BEIJER ELECTRONICS AB, INCLUDING ALL ITS GROUP
COMPANIES, SHALL NOT BE LIABLE TO ANYONE FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE INSTALLATION, USE OR REPAIR
OF THIS EQUIPMENT, WHETHER ARISING IN TORT, CONTRACT,
OR OTHERWISE. BUYER'S SOLE REMEDY SHALL BE THE REPAIR,
REPLACEMENT, OR REFUND OF PURCHASE PRICE, AND THE
CHOICE OF THE APPLICABLE REMEDY SHALL BE AT THE SOLE
DISCRETION OF BEIJER ELECTRONICS AB, INCLUDING ALL ITS
GROUP COMPANIES.
Head of
fi
ce
Beijer Electronics AB
Box 426
201 24 Malmö, Sweden
www.beijerelectronics.com / +46 40 358600
