Behringer X-DANTE Quick Start Manual Download Page 3

Terminals marked with this 

symbol carry electrical 
current of sufficient 

magnitude to constitute risk of electric 
shock. Use only high-quality 
professional speaker cables with ¼" TS 
or twist-locking plugs pre-installed. 
All other installation or modification 
should be performed only by 
qualified personnel.

This symbol, wherever it 

appears, alerts you to the 
presence of uninsulated 

dangerous voltage inside the enclosure 
- voltage that may be sufficient to 
constitute a risk of shock.

This symbol, wherever it 
appears, alerts you to 
important operating and 

maintenance instructions in the 
accompanying literature. Please read 
the manual.

Caution

To reduce the risk of electric 
shock, do not remove the 

top cover (or the rear section). No user 
serviceable parts inside. Refer servicing to 
qualified personnel.

Caution

To reduce the risk of 
fire or electric shock, 

do not expose this appliance to rain 
and moisture. The apparatus shall not 
be exposed to dripping or splashing 
liquids and no objects filled with 
liquids, such as vases, shall be placed on 
the apparatus.

Caution

These service instructions 
are for use by qualified 

service personnel only. To reduce the 
risk of electric shock do not perform any 
servicing other than that contained in 
the operation instructions. Repairs have 
to be performed by qualified 
service personnel.

1.  

Read these instructions.

2.  

Keep these instructions.

3.  

Heed all warnings.

4.  

Follow all instructions.

5.  

Do not use this apparatus 

near water.

6.  

Clean only with dry cloth.

7.  

Do not block any ventilation 

openings. Install in accordance with the 
manufacturer’s instructions.

8.  

Do not install near any heat sources 

such as radiators, heat registers, 
stoves, or other apparatus (including 
amplifiers) that produce heat.

9.  

Do not defeat the safety purpose of 

the polarized or grounding-type plug. 
A polarized plug has two blades with 
one wider than the other. A grounding-
type plug has two blades and a third 
grounding prong. The wide blade or the 
third prong are provided for your safety. 

If the provided plug does not fit into 
your outlet, consult an electrician for 
replacement of the obsolete outlet.

10.  

Protect the power cord from 

being walked on or pinched particularly 
at plugs, convenience receptacles, 
and the point where they exit from 
the apparatus.

11.  

Use only attachments/accessories 

specified by the manufacturer.

12.  

Use only 

with the cart, 
stand, tripod, 
bracket, or table 
specified by the 

manufacturer, or sold with the apparatus. 
When a cart is used, use caution when 
moving the cart/apparatus combination 
to avoid injury from tip-over.

13.  

Unplug this apparatus during 

lightning storms or when unused for long 
periods of time. 

14.  

Refer all servicing to qualified 

service personnel. Servicing is required 
when the apparatus has been damaged 
in any way, such as power supply cord or 
plug is damaged, liquid has been spilled 
or objects have fallen into the apparatus, 
the apparatus has been exposed to rain 
or moisture, does not operate normally, 
or has been dropped.

15.  

The apparatus shall be connected to 

a MAINS socket outlet with a protective 
earthing connection.

16.  

Where the MAINS plug or an 

appliance coupler is used as the 
disconnect device, the disconnect device 
shall remain readily operable.

Important Safety 

Instructions

3

Quick Start Guide

Summary of Contents for X-DANTE



















Reviews: