Behringer X-DANTE Quick Start Manual Download Page 17

17

Quick Start Guide

FEDERAL COMMUNICATIONS 
COMMISSION COMPLIANCE 
INFORMATION

Responsible Party Name: 

MUSIC Group Services NV Inc.

Address: 

5270 Procyon Street  

Las Vegas, NV 89118  

USA

Phone Number: 

+1 702 800 8290

EXPANSION CARD X-DANTE

complies with the FCC rules as mentioned in the following paragraph:

This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference in 
a residential installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference 
to radio or television reception, which can be determined by turning 
the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:

• 

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and receiver.

• 

Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected.

• 

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC rules. Operation is subject to 
the following two conditions:

(1) this device may not cause harmful interference, and  
(2) this device must accept any interference received, including 
interference that may cause undesired operation.

Important information:

Changes or modifications to the equipment not expressly approved by 
MUSIC Group can void the user’s authority to use the equipment.

EXPANSION CARD X-DANTE

Summary of Contents for X-DANTE



















Reviews: