5
ULTRABASS BX4410/BX4410A
2. CONTROL ELEMENTS
1.2.3 Online registration
Please do remember to register your new BEHRINGER
equipment right after your purchase by visiting
www.behringer.com (alternatively www.behringer.de) and
kindly read the terms and conditions of our warranty carefully.
Should your BEHRINGER product malfunction, our goal is to
have it repaired as quickly as possible. To arrange for warranty
service, please contact the retailer from whom the equipment
was purchased. Should your BEHRINGER dealer not be located
in your vicinity, you may directly contact one of our subsidiaries.
Corresponding contact information is included in the original
equipment packaging (Global Contact Information/European
Contact Information). Should your country not be listed, please
contact the distributor nearest you. A list of distributors can be
found in the support area of our website (www.behringer.com).
Registering your purchase and equipment with us helps us
process your repair claims quicker and more efficiently.
Thank you for your cooperation!
2. CONTROL ELEMENTS
2.1 Front panel
Fig. 2.1: BX4410/BX4410A front panel (section 1)
The
LEVEL
VU meter reads the level that is applied to the
preamp circuitry of the BX4410/BX4410A.
+
If the GAIN control
is set fully counterclockwise,
the VU meter reads the input level only. Selecting
Active
instead of Passive is recommended
if the input level appears too high (in the right-hand
third of the VU meter). Use the GAIN control to set
the amplifier properly (so that the meter is in the
mid region). The overall volume can be adjusted
with the OUTPUT control
.
These are the inputs for your electric bass guitar. The
PASSIVE
jack is for passive basses, the
ACTIVE
jack for
active instruments with high output levels. The ACTIVE
jack features 10 dB less gain.
Use the
GAIN
control to determine the input gain on your
BX4410/BX4410A.
Connect your footswitch to the
FOOTSWITCH
jack, so
as to control the sub-harmonics processor and SHAPE
filter.
With the sub-harmonics processor switched on (see
)
you can add ultra-low bass frequencies to your sound by
turning the
ULTRABASS
control (see chapter 5).
Press the
ULTRABASS
switch to enable the sub-harmonics
processor: The LED above the switch lights up.
Fig. 2.2: BX4410/BX4410A front panel (section 2)
The
BASS
control in the EQ section allows you to boost or
cut the bass frequencies at approx. 50 Hz.
Press the
DEEP
switch to add low frequencies (ranging
from 30 - 200 Hz) to your bass sound. When the DEEP
function is switched on, the LED above the switch lights up.
This control governs the upper bass-frequency range at
approx. 140 Hz.
The
MIDDLE
control allows you to boost/cut the low
midrange frequencies at approx. 500 Hz.
This control raises/lowers the high midrange frequencies
at approx. 1.6 kHz.
The
TREBLE
control governs the high-frequency range
on your BX4410/BX4410A at approx. 7.5 kHz.
Use this switch to enable/disable the
BRIGHT
effect, which
adds some brilliance to the treble frequencies in the range
from 2 - 20 kHz. When the BRIGHT function is on, its
respective LED lights up.
Fig. 2.3: BX4410/BX4410A front panel (section 3)
When you enable the SHAPE filter with switch
, you
can use the
SHAPE
control to modify the filter sound. The
filter position is adjustable in the range from 120 Hz - 1.2 kHz.
The
SHAPE
switch activates the SHAPE filter. When the
filter is on, the LED above the switch lights up.
Use the
OUTPUT
control to determine the overall volume
of your BX4410/BX4410A.
