Power Connection
The 182 ANALOG SEQUENCER module comes with the required
power cable for connecting to a standard Eurorack power supply
system. Follow these steps to connect power to the module. It
is easier to make these connections before the module has been
mounted into a rack case.
1.
Turn the power supply or rack case power off and
disconnect the power cable.
2.
Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3.
Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4.
After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of fi xed holes
spaced 2 HP apart along the length of the case, or a track that
allows individual threaded plates to slide along the length
of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded
plate. Attach the screws part way to start, which will allow small
adjustments to the positioning while you get them all aligned. After
the fi nal position has been established, tighten the screws down.
Specifi cations
Inputs
Tempo CV input
Type
3.5 mm TS jack, DC coupled
Impedance
100 kΩ, unbalanced
Max input level
+10 V
CV scaling
1 V/oct.
Trigger input
Type
3.5 mm TS jack, DC coupled
Impedance
30 kΩ, unbalanced
Max input level
+10 V
Outputs
CV output
Type
2 x 3.5 mm TS jacks, DC coupled
Impedance
600 Ω, unbalanced
Max output level
+5 V
Gate output
Type
3.5 mm TS jack, DC coupled
Impedance
600 Ω, unbalanced
Max output level
+5 V
Trigger output
Type
3.5 mm TS jack, DC coupled
Impedance
3 kΩ, unbalanced
Max output level
+5 V
Controls
Step CV level
0 V to +5 V
Tempo
0.14 Hz to 33 Hz
Delay
0 to 10 s
Gate time
10 % to 90 % duty cycle
Step number
1 to 8 steps
Step switch
Repeat / manual / single
Start/stop switch
Momentary
Parallel/series switch
8 step / 16 step
Power
Power supply
Eurorack
Current draw
30 mA (+12 V), 30 mA (-12 V)
Physical
Dimensions
43 x 81 x 129 mm (1.7 x 3.2 x 5.1")
Rack units
16 HP
Weight
0.17 kg (0.37 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suff ered by any person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specifi cations, appearances and other information are subject to change without notice. All trademarks are the property
of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone and Coolaudio are
trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2020 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty,
please see complete details online at musictribe.com/warranty.
