Bedrock AM100 Operating Manual Download Page 92 | Manualshive

Page: 92 / 119

background image

92

Bedrock AM100 operating manual

© Bedrock Audio BV, 2021

18.3. Recovery mode

If the internal operating system or software of the Bedrock AM100 gets corrupted, because
of a failed firmware update or otherwise, the system can usually be restored through the
internal recovery mode.

To enter recovery mode, make sure the device is turned off (shutdown can be forced by
keeping the on/off button pressed for >5 seconds).

Then take the following steps:

•

Start the device by pressing the power button. Press the button briefly and
release, until the LED lights up.

•

After a very short interval (<1 second) the LED turns green. As soon as this
happens, press the power button again and keep it pressed down.

•

Timing is critical; it may take a few attempts to get it right. It is a short press
to start the device, followed by a long press as soon as the LED turns green.

•

Wait for the AM100 to initiate recovery mode. You will see the screen below.

The device can now be accessed through USB. This means you can copy a new .EAP
update package to the UPDATES folder. If you are having trouble accessing USB in the
normal operating modes of the AM100, this may be a way to restore your system and re-
install the latest firmware.

«
...
90
91
92
93
94
...
»

Summary of Contents for AM100
























































































































Reviews:

No comments

Related manuals for AM100

Brand: Keller Pages: 6

SMatrix DMX2400

Brand: dallmeier Pages: 12

Brand: Danfoss Pages: 6

Brand: Gardner Bender Pages: 7

Surface Scatter 7 sc

Brand: Hach Pages: 6

Brand: Hach Pages: 118

Brand: Hach Pages: 388

Orbisphere 51 Series

Brand: Hach Pages: 118

ORBISPHERE 3650 Atex

Brand: Hach Pages: 51

Brand: Hach Pages: 72

POLYMETRON 8362

Brand: Hach Pages: 78

Pocket Colorimeter II

Brand: HACH LANGE Pages: 146

Brand: Hach Pages: 146

Brand: Hach Pages: 36

PHOSPHAX indoor sc

Brand: Hach Pages: 104

Lange ORBISPHERE 3100

Brand: Hach Pages: 384

Brand: Hach Pages: 172

Brand: Rayjet Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands