manualshive.com logo in svg

Beckman Coulter J-Lite JLA 16.250, Instruction Manual

Share
Download
Beckman Coulter J-Lite JLA 16.250 Instruction Manual Download Page 26

26

J-Lite JLA-16.250 Rotor

SUPPLY LIST

Call Beckman Coulter Sales (1-800-742-2345 in the United States) or 
your local Beckman Coulter office, or see the 

Beckman Coulter High 

Performance, High Speed, High Capacity Rotors, Tubes & Accesso-
ries

 catalog (BR-8102, available at www.beckman.com) for detailed 

information on ordering parts and supplies. For your convenience, a 
partial list is given below.

NOTE

Publications referenced in this document can be 
obtained by calling Beckman Coulter at 1-800-
742-2345 in the United States, or by contacting 
your local Beckman Coulter office.

REPLACEMENT ROTOR PARTS

JLA-16.250 rotor assembly, biosafe (with dual-locking lid)  . . . . . .  363930
JLA-16.250 rotor assembly (with single-locking lid) . . . . . . . . . . . .  363934
Dual-locking lid assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  363931
Single-locking lid assembly  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  363935
Large lid O-ring (qty/2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  893502
Small lid O-ring (qty/2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  893503

SUPPLIES

Bottles, tubes, and adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  see Table 3
Rotor Cleaning Kit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  339558
Silicone vacuum grease (1 oz)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  335148
Solution 555 (1 qt). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  339555
Spinkote lubricant (2 oz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  306812

Summary of Contents for J-Lite JLA 16.250































Reviews:

No comments

Brands by name

Popular brands

Load more brands