manualshive.com logo in svg

Beckman Coulter J-Lite JLA 16.250, Instruction Manual

Share
Download
Beckman Coulter J-Lite JLA 16.250 Instruction Manual Download Page 10

10

J-Lite JLA-16.250 Rotor

5. Once the rotor is properly aligned carefully lower it straight down 

onto the hub. 

Do not drop the rotor onto the hub

.

6. Slowly turn the rotor around the drive spindle to make sure that it 

is properly seated. In rare cases, the rotor pins can rest on top of 
the spindle hub pins or teeth, which prevents the rotor from being 
secured to the drive spindle. Turning the rotor after installing it 
will move the pins into proper position.

Figure 3. Rotor Top View: Indicator Marks Show Drive Pin Orientation

7. Secure the rotor to the centrifuge drive spindle as follows:

Dual-locking lid

: press the lid knob down and turn it to the right 

(clockwise) until secure, no more than two full turns. Do not 
overtighten.

Single-locking lid

: place filled tubes into the rotor, then place the 

lid on the rotor. Press the lid knob down and turn it to the right 
(clockwise) until secure. Do not overtighten.

WARNING

!

If the rotor is left in the centrifuge between 
runs, make sure that the rotor is seated on the 
drive hub and that the tie-down knob is tight 
before each run.

Tie-down Knob

Knob Threads

Single-Locking Lid

Indicator Marks

Summary of Contents for J-Lite JLA 16.250































Reviews:

No comments

Brands by name

Popular brands

Load more brands