Beckhoff PS3031-2440-0000 Documentation Download Page 30 | Manualshive

Page: 30 / 44

background image

Technical data, mounting, wiring

PS3031-2440-0000

30

Version: 1.0

3.20

Dimensions and weight

Dimensions and weight

Overall width

110 mm

Height

124 mm

Depth

127 mm
The height of the DIN rails must be added to the depth of the device to
calculate the total installation depth required

Weight

1500 g

DIN rail

Use 35 mm DIN rails according to EN 60715 or EN 50022 with a height of 7.5
or 15 mm.
The height of the DIN rail must be added to the depth of the device (127 mm)
to calculate the total installation depth required.

Housing material

Housing: Aluminum alloy Cover: Steel

Installation clearances

See chapter on

Safety instructions and installation requirements [

Fig. 20: Front/side view of PS3031-2440-0000, all specifications in mm

«
...
28
29
30
31
32
...
»

Summary of Contents for PS3031-2440-0000













































Reviews:

No comments

Related manuals for PS3031-2440-0000

Brand: Fein Pages: 70

Brand: yellow jacket Pages: 2

Brand: Würth Pages: 8

Brand: Koch Pages: 76

POWERPLUS POWX00416

Brand: VARO Pages: 8

Brand: Milwaukee Pages: 117

Brand: Baileigh Pages: 20

Brand: Grizzly Pages: 80

Brand: TAKASAGO Pages: 192

Brand: M-system Pages: 2

Brand: Stanley Pages: 32

Brand: MaxPro Pages: 112

Brand: Panduit Pages: 2

Brand: F.F. Group Pages: 48

Brand: Nissei Pages: 2

Brand: XTline Pages: 76

Brand: Truper Pages: 24

SCI 7660 SERIES

Brand: Epson Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands