manualshive.com logo in svg

Beckhoff KL6811, Documentation

Share
Download
Beckhoff KL6811 Documentation Download Page 56

Appendix

KL6811

56

Version: 2.0.0

Special commands

You may find the special commands and further information in the 

DIN EN 60929 [

}

 56]

 standard.

7.2

Bibliography

Books

• DALI manual published by DALI AG (DALI Activity Group, see 

http://www.dali-ag.org

).

Standards

• DIN EN 60929: Standard for AC-supplied electronic ballasts for tubular fluorescent lamps (IEC 60929),

Annex E.

7.3

Support and Service

Beckhoff and their partners around the world offer comprehensive support and service, making available fast
and competent assistance with all questions related to Beckhoff products and system solutions.

Beckhoff's branch offices and representatives

Please contact your Beckhoff branch office or representative for 

local support and service

 on Beckhoff

products!

The addresses of Beckhoff's branch offices and representatives round the world can be found on her internet
pages:

http://www.beckhoff.com

You will also find further 

documentation

 for Beckhoff components there.

Beckhoff Headquarters

Beckhoff Automation GmbH & Co. KG

Huelshorstweg 20
33415 Verl
Germany

Phone:

+49 5246 963 0

Fax:

+49 5246 963 198

e-mail:

[email protected]

Beckhoff Support

Support offers you comprehensive technical assistance, helping you not only with the application of
individual Beckhoff products, but also with other, wide-ranging services:

• support

• design, programming and commissioning of complex automation systems

• and extensive training program for Beckhoff system components

Hotline:

+49 5246 963 157

Fax:

+49 5246 963 9157

e-mail:

[email protected]

Beckhoff Service

The Beckhoff Service Center supports you in all matters of after-sales service:

Summary of Contents for KL6811





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands