manualshive.com logo in svg

Beckhoff CX20 0 Series, Manual, Page: 50 / 92

Share
Download
Beckhoff CX20 0 Series Manual Download Page 50

Configuration

CX20x0

50

Version: 2.5

7.2.4

Restoring the Beckhoff real-time driver.

The Beckhoff real-time driver can be restored if the real-time driver was uninstalled or the original Intel®
driver for jumbo frames or NIC Teaming was installed, for example. This chapter shows you how to use

TcRteInstall.exe

 to restore the Beckhoff real-time driver. The file is in the TwinCAT directory by default.

Requirements:

• You can find the 

TcRteInstall.exe

 in a TwinCAT 2 standard installation under: 

C:

\TwinCAT\Io\TcRteInstall.exe

• And in a TwinCAT 3 standard installation under: 

C:\TwinCAT\3.1\System\TcRteInstall.exe

Proceed as follows:

1. Double-click the 

TcRteInstall.exe 

file.

The installation dialog appears and shows the compatible Ethernet interfaces under 

Compatible

devices

.

2. Select the Ethernet interfaces for which you wish to restore the Beckhoff real-time driver and click on

Install

.

ð

The Beckhoff real-time driver is installed. The Ethernet interfaces with installed Beckhoff real-time driver
are shown under 

Installed and ready to use devices (real-time capable)

.

Summary of Contents for CX20 0 Series





























































































Reviews:

No comments