background image

 

Operating Instructions 

 

 

 

Maintenance 

 

Please also refer to chapter 

General instructions

 
 

Cleaning the Industrial PC 

 

Danger

 

 

Switch off the Industrial PC and all connected devices, and disconnect the 
Industrial PC from the power supply. 

 

 

 

 

The Industrial PC can be cleaned with a soft, damp cloth. Do not use any 
aggressive cleaning materials, thinners, scouring material or hard objects 
that could cause scratches. 

 
 

Replacing the battery on the motherboard 

 

A used battery on the motherboard has to be replaced according to the 
rules of the board manufactorer. 

 

Danger

 

 

Danger of Explosion if battery is incorrectly replaced. Replace only with 
same or equivalent type recommended by the manufacturer. Dispose of 
used batteries according to the manufacturer's instructions.

 

 
 

Servicing 

 

The Industrial PC requires no maintenance. 

 
 

Shutting down 

 

Disposal 

Dismantling the Industrial 
PC 
 
Observe national 
electronics scrap 
regulations 

The device must be fully dismantled in order to dispose of it. The housing 
can be sent for metal recycling. 
 
Electronic parts such as disk drives and circuit boards must be disposed of 
in accordance with national electronics scrap regulations. 

 
 

 CP64xx 

15 

Summary of Contents for CP64 Series





















Reviews: