BEC MX-241NP Quick Start Manual Download Page 3

BEC MX-241NP 4G/LTE CBRS Wi-Fi Router 

 

 

 

 

 

 

LED 

STATUS 

DESCRIPTION 

Power 

 

 

Green 

System is up and ready 

Red 

Boot failure 

Ethernet Port LAN 
1 - 2 

Green 

Transmission speed is at Gigabit speed (1000Mbps) 

Orange 

Transmission speed is at 10/100Mbps 

Blinking 

Data being transmitted/received 

Wireless 

 

Green 

Wireless connection established 

Green blinking 

Data being transmitted / received 

Orange 

WPS configuration is in progress 

 

LTE       
(Received Signal   

Strength Indicator)

 

Green 

RSSI greater than -69 dBm.    Excellent signal condition 

Green Flashing quickly 

RSSI from -81 to -69 dBm. Good signal condition 

Orange Flashing quickly 

RSSI from -99 to -81 dBm.    Fair signal condition. 

Orange Flashing slowly 

RSSI less than -99 dBm. Poor signal condition. 

Orange 

No signal and the cellular module is in service 

Off 

No LTE module or LTE module fails 

Green & Orange 

MX-241NP is either in debug mode or in upgrading 

firmware process 

Internet   

 

Green 

IP address has received; traffic is passing thru the device. 

Red 

IP address request has failed. 

Off 

MX-241NP is either in bridged mode or WAN connection 
not ready. 

Front Panel LEDs 

Summary of Contents for MX-241NP













Reviews: