BeamMed Sunlight Omnisense 7000S User Manual Download Page 79 | Manualshive

Page: 79 / 284

background image

Omnisense 7000S/8000S

4-15

Cable Connections

S

TEP

3 Connect Probes

Probes should be attached to the unit during initial
setup and left connected at all times. After initial
setup, probes are connected/disconnected only
when adding new probes or transporting
Omnisense.

The correct procedure for connecting probes is
illustrated in the following photograph.

Figure 4.9

Pins on a probe connector

S

TEP

4 Electrical Power Connection

The following are normally done once, during ini-
tial setup.

•

Note carefully the power rating of your
Omnisense unit (230 or 110 V autoswitchable)
and insure that you are using an electrical outlet
with either rating.

•

Ensure that the main unit power switch (in the
front panel) is off.

•

Attach the Omnisense unit power cable to the
appropriate socket on the rear panel ("9 AC
power inlet" in 4.2 on page 4-6). Plug the other
end of the cable into a standard electrical outlet.

Note carefully the arrangement of
pins on the probe connector. Ensure
that you insert the connector into a
probe socket so that corresponding
pins are aligned. Probes may be
inserted into either of the two left-
side sockets. Press the connector
firmly into its socket. Tighten the
locking screws, as this ensures
proper electrical ground. Repeat this
procedure for the second probe and
tighten locking screws.

«
...
77
78
79
80
81
...
»

Summary of Contents for Sunlight Omnisense 7000S





























































































































































































































































































Reviews:

No comments

Related manuals for Sunlight Omnisense 7000S

Brand: ABB Pages: 6

SafetuNet Alert

Brand: Masimo Pages: 2

medialon Showmaster Go

Brand: 7th Sense Pages: 9

LOUDEN 200 Series

Brand: ACCO Brands Pages: 144

Brand: B&K Pages: 16

Brand: B&G Pages: 2

Brand: UEi Pages: 5

Brand: UGO BASILE Pages: 47

Brand: UFO Pages: 16

Brand: Xaoc Devices Pages: 8

Sonorex Super RK 31

Brand: BANDELIN Pages: 21

BTL7-A/E501-M Series

Brand: Balluff Pages: 194

Brand: B.Pro Pages: 48

Brand: ABB Pages: 16

Brand: ABB Pages: 2

Brand: Öhlins Pages: 8

Brand: ?HC Pages: 2

Firefly Low Voltage Lighting System

Brand: Ultra Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands