background image

75.5897.02 LZR-H110 20170821   

Page 11 of 12

TROUBLESHOOTING

No blue LED

No power

Check cable and connexion.

Polarity of power supply is 
inverted

Check the polarity of the power supply.

All LEDs have been deactivated 
by remote control

Activate LEDs using remote control.

Detection LED remains 
green

Detection field too small or 
deactivated

Check size of fields.

Launch a teach-in.

Detection LED remains red

Someone/Something is in the 
detection field

Step out of the field and/or remove the 

any object(s) from the field.

Field is touching floor/wall/
barrier – this leads to detection

Activate the 3 red beams and check if the 

position of the sensor is correct.  If not, 

adjust the hex screws.

Verify the field size.

Launch a teach-in.

Orange LED flashing and 
detection LEDs are red

No background (reference 
point) is found

Check position of sensor.

Check the mounting side setting.  If no 

reference point is found, set the mounting 

side to value 3 or 4.

Launch a new teach-in.

Sensor is masked

Verify and clean the front screens with a 

damp cloth.

Orange LED is on

Power supply voltage exceeds 
acceptable limits

Check power supply voltage.

Sensor exceeds temperature 
limits

Verify the temperature of the environment. 

Protect the sensor from sunlight using a 

cover, if necessary.

Internal error

Wait a few seconds. 

If the LED remains ON, reset the power 

supply. 

If the LED turns on again, replace the 

sensor.

Sensor does not respond 
to the reote control

Remote control batteries not 
installed properly or are dead

Check battery orientation or replace the 

batteries.

Remote control not pointed 
correctly

Point the remote control towards the 

sensor, but with a slight angle. The RC 

should not be pointed in a right angle in 

front of the sensor.

Reflective object is close to the 
sensor

Avoid highly reflective material in proximity 

to the sensor.

Sensor does not unlock

Access code needs entered or 
an incorrect code was used

Cut and restore power supply. 

No code is required to unlock during the 

first minute after powering.

75.5897.02 LZR-H110 20170821   

Page 11 of 12

OBSOLETE

Summary of Contents for LZR-H110













Reviews: