BEA JAMB CAM User Manual Download Page 4

Page 4 of 4  

75.5779.01 JAMB CAM 20131115

Upon completion of the installation or service work, at a minimum, perform a daily safety check in accordance with the

minimum inspection guidelines provided by AAADM. Provide each equipment owner with an owner’s manual that 

includes a daily safety checklist and contains, at a minimum, the information recommended by AAADM. Offer an 

information session with the equipment owner explaining how to perform daily inspections and point out the location of 

power/operation switches to disable the equipment if a compliance issue is noted. The equipment should be inspected 

annually in accordance with the minimum inspection guidelines. A safety check that includes, at a minimum, the items 

listed on the safety information label must be performed during each service call. If you are not an AAADM certified 

inspector, BEA strongly recommends you have an AAADM certified inspector perform an AAADM inspection and place 

a valid inspection sticker below the safety information label prior to putting the equipment into operation.

A

A

ADM

American Association of

 

Automatic Door Manufactures

 

     ANSI / AAADM Compliance

TECHNICAL SPECIFICATIONS

Power Supply

6.6 - 36 VDC (+/- 10%) 
6 - 28 VAC (+/- 10%)

Operating Temperature

-30° to 60° C (RH 95% max)

Video Output

1.0 (Vp-p) / 75Ω

Image Sensor

CMOS

Horizontal Resolution

480 TVL

NTSC Output

720 (H) x 480 (V)

Sync System

Inter-Sync

Frame Rate

30 fps

Minimum Illumination

0.01 LUX

AE Control

Auto

Gain Control

Auto

Electronic Shutter

1 s ~ 1/10,000 s

S/N Ratio

>50 dB

AWB

Auto

Specifications are subject to change without prior notice.
All values measured in specific conditions.

PLEASE KEEP FOR FUR

THER USE - DESIGNED FOR COLOR PRINTING

©BEA

 | Original Instructions | 

75.5779.01 JAMB CAM 20131115

24/7 Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462 | General Tech Questions: [email protected] | Tech Docs: www.beasensors.com

TROUBLESHOOTING

No image displaying

Power not connected

Connect power wires

Power not correct

Verify appropriate voltage

Bad camera

Replace camera

Image upside down

Camera rotated incorrectly

Rotate camera 180 degrees

Distorted image

Power not correct (too low)

Verify appropriate voltage, increase

Bad camera

Replace camera

Dirty window

Clean window

Summary of Contents for JAMB CAM

Page 1: ... Phillips 0 Phillips 2 1 8 Drill Bit 1 1 4 Drill Bit Multimeter Caulk Caulking Gun COMPONENTS REQUIRED TOOLS DESCRIPTION PART NUMBER CMOS Camera 12 1000 2 5 mm Lens 50 5277 Power Video Harness 20 5316 Housing 70 5528 Housing Screws 50 1818 Camera Screws 50 5276 User s Guide 75 5779 Mounting Template 75 5780 1 camera 2 housing 3 power supply video harness 1 2 3 ...

Page 2: ...n of installation DO NOT attempt any internal repair of the components All repairs and or component replacements must be performed by BEA Inc Unauthorized disassembly or repair 1 May jeopardize personal safety and may expose one to the risk of electrical shock 2 May adversely affect the safe and reliable performance of the product resulting in a voided warranty PRECAUTIONS The device should not be...

Page 3: ...unting on LEFT jamb camera wire should lead towards housing window out of housing and if mounting on RIGHT jamb camera wire should lead away from housing window into housing 4 Plug camera into power video harness 5 Route power video harness up jamb into door header 6 Connect RCA video out from power video harness into appropriate RCA video in 7 Wire nut red and black power wires to external transf...

Page 4: ...bel prior to putting the equipment into operation A AADMAmerican Association of Automatic Door Manufactures ANSI AAADM Compliance TECHNICAL SPECIFICATIONS Power Supply 6 6 36 VDC 10 6 28 VAC 10 Operating Temperature 30 to 60 C RH 95 max Video Output 1 0 Vp p 75Ω Image Sensor CMOS Horizontal Resolution 480 TVL NTSC Output 720 H x 480 V Sync System Inter Sync Frame Rate 30 fps Minimum Illumination 0...

Reviews: