BEA IS40 Installation Manual Download Page 7

75.5695.07 IS40 IS40XL 20170313 

Page 7 of 9

5

DOOR

DOOR

DOOR

DOOR

2

3

7

5

6

2

5

6

1

1

2

3

4

7

5

6

1

2

3

4

7

5

6

1

DOOR

DOOR

DOOR

DOOR

DOOR

5

2

1

7

5

1

2

1

7

5

2

1

7

5

2

1

5

FREQUENCY

MAX. PRESENCE 
DETECTION TIME

IR-CURTAIN
IMMUNITY

MIN. SIZE 
OF TARGET

IR-DETECTION FIELD

low

normal high

1 min

2 min

30 s

10 min 20 min

5 min

1 h

2 h

1 h 30

POSSIBLE REMOTE CONTROL SETTINGS 

(presence sensing)

SETUP

MAX. PRESENCE 
DETECTION TIME

AIR-CURTAIN
IMMUNITY

low

normal high

1 min

2 min

30 s

10 min 20 min

5 min

1 h

2 h

1 h 30

A

B

FREQUENCY

TARGET
SIZE

AIR-PATTERN SIZE

The target position 

within the AIR field 

is random.

low

high

1 min

2 min

30 s

10 min 20 min

5 min

1 h

2 h

1 h 30

normal

AIR PATTERN 
SIZE

AVAILABLE TARGET SIZE

1

2

3

4

5

9

8

7

6

The target position  within the "AIR" Field is random

FACTORY VALUES

RESETTING TO FACTORY VALUES:

Launch a setup to make a reference picture.

Step out of the detection field and do not leave any tools inside the detection field.

Upon power-up, the sensor launches a short setup.

IMPORTANT

: Perform a functional test for proper operation before leaving the site.

*no

learn

* not  

guaranteed

IMPORTANT

: Always finish an adjustment session by launching a setup 

(see step 5)

and test the proper operation of the installation before leaving the premises. 

NOTE: 

 TARGET SIZE MUST BE CAPABLE TO FIT INSIDE THE CHOSEN AIR PATTERN SIZE

Summary of Contents for IS40










Reviews: