BEA IS40 Installation Manual Download Page 6

Page 6 of 9 

75.5695.07 IS40 IS40XL 20170313

3

4

5

6

1

2

XXS

XS

S

>

>

>

>

L

XL

XXL

0.5 s

1 s

2 s

3 s

4 s

5 s

6 s

7 s

8 s

9 s

Mounting Height

8 ft

10 ft

11.5 ft

13 ft
16 ft

Maximum Mounting Height

IS40XL                        11.5 ft

IS40                            16 ft

Width *

5 ft
7 ft

7.5 ft

8.5 ft

10 ft

Depth *

5 ft
7 ft

7.5 ft

8.5 ft

10 ft

OUTPUT 

CONFIGURATION

PRESENCE RELAY

IS40 / IS40XL

LED

0 - 6:  ALL MODES

Activates when object is in presence zone.

ACTIVATION RELAY

IS40 / IS40XL

LED

0:  STANDARD MODE

Activates when motion detected.

1:  PULSE ON ENTRY

Activates if object motion is detected and then object 

enters presence zone.

2:  PULSE ON EXIT

Activates if object motion is detected and then object exits 

presence zone.

3:  PULSE ON ENTRY FIRST / LAST LINE

     (See Example to the Left)

Activates if object motion is detected and then object 

enters presence zone (first or last line).

4:  PULSE ON EXIT FIRST / LAST LINE

     (See Example to the Left)

Activates if object motion is detected and then object exits 

presence zone (first or last line).

5:  REMAINS ACTIVE UNTIL PRESENCE 

     ZON E IS CLEARED (Regardless of Motion)

Activates when motion is detected and remains active until 

the presence zone is cleared.

6:  REMAINS ACTIVE UNTIL PRESENCE

     ZONE IS CLEARED (Regardless of Motion)

Activates when motion is detected and AIR is detected and 

remains active until the presence zone is cleared.

bi

uni

POSSIBLE REMOTE CONTROL SETTINGS 

(motion sensing)

FIELD SIZE
(SENSITIVITY)

DETECTION MODE

uni

AWAY

DETECTION FILTER
(REJECTION MODE)

bi = two-way detection

uni = one-way detection towards sensor

uni AWAY = one-way detection away from sensor

3     Low ‘Pedestrian/Parallel traffic’ Rej Interference    

         Immunity

4     Medium ‘Pedestrian/Parallel traffic’ Rej Interference       

       Immunity

5     High ‘Pedestrian/Parallel traffic’ Rej Interference     

         Immunity

6     Extra High ‘Pedestrian/Parallel traffic’ Rej           

       Interference Immunity

1    Detection of all kind of Targets in Motion
2    Detection of all kind of Targets in     

        Interference Immunity

    

Detection of ALL TARGETS

(pedestrians, vehicles and parallel traffic are detected)

Detection only of VEHICLES MOVING TOWARDS THE SENSOR

(pedestrians and parallel traffic are not de immunity filter)

AIR PATTERN SIZE AT 15

O

 SENSOR ANGLE

Approximate default AIR pattern size using a 15º sensor tilt angle. The higher the mounting height the larger the AIR 
pattern.

*      Dimensions are approximate.

HOLD-OPEN TIME

Red

Green 

DOOR  EXAMPLE

First Line

Last Line

Summary of Contents for IS40










Reviews: