14
15
Storage
• When your pressure washing
session has been completed, turn
off the power switch located on
the front of the power washer.
Unplug the power cord from
the outlet. Turn off the water
supply. Pull the trigger on the
spray gun 2-3 times to drain out
the excess water and to release
any remaining water pressure.
Disconnect the garden hose
adapter from the water inlet. DO
NOT allow the power washer to
run with no water flowing through
it.
• Remove detergent bottle and
clean completely. Residual
chemical will stick to the
container and can cause the
detergent injector to clog and not
function properly.
• Remove high pressure hose from
spray gun.
•
Remove lance from the gun. Place
the gun in the holder on the side.
Lances are placed into any of the
slots in the back of the unit. Make
sure to discard any remaining
detergent from the bottle. Flush
the bottle and nozzle head with
fresh water to prevent clogging.
• Hook the power cord around the
L-shaped tab on the right side of
the machine when facing it.
• The pressure hose is stored on the
hose hook located on the back of
the handle.
PUMP SAVER
Pump Saver is a product that
protects and prolongs the life of the
pump. This will keep the internal
parts of the pump lubricated and
protected from freezing while
being stored in ALL climates. It
also assists with protection from
internal corrosion. The BE part # is:
85.490.046 (16oz. bottle).
Pump Saver Instructions
Follow the previous storage
instructions for your power washer.
To prevent staining, protect the
surface under the power washer from
any excess fluid. Wear eye protection
when using this product.
Turn unit off and disconnect the
gun before adding pump protector.
Unscrew threaded top from bottle to
remove seal and reattach threaded
top to bottle.
Remove black cap from bottle.
1) Place top of pump saver bottle
onto the garden hose adapter
previously installed to pressure
washer inlet.
2) Secure pump saver bottle by
turning in a clockwise direction.
13
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
CARE AND MAINTENANCE
Detergents
• Use detergents designed for power washers. These
can be purchased online at our website www.
arblueclean.com. Hardware stores or home centers
also have power washer detergents for different
cleaning projects. The cleaning solution should be
the consistency of water in order to prevent clogging
your detergent bottle and nozzle.
• This system applies detergent under low pressure.
The cleaning power of the detergents is enhanced
when applied with low pressure and enough time is
given to break down dirt and grime. The combination
of low pressure and chemical action is very effective
and can be better than scrubbing if applied properly.
ALWAYS
spray detergent on a dry surface.
DO NOT
pre-soak area. Wetting the surface first dilutes
the detergent and reduces its cleaning ability.
DO
NOT
allow detergent to dry on surface. On vertical
surfaces being cleaned, apply detergent to lower
surfaces and work your way up to prevent detergent
from causing streaks in the dirt and grime. Rinse
detergent by pressure washing from bottom up for
same reason.
• If a stain is particularly tough, it may be necessary
to reapply the detergent and use a bristled brush to
scrub the stain. Subsequent power washing after
brushing should successfully complete your cleaning
job.
Cleaning Garden Hose Adapter
• The screens inside the clear garden hose adapter
should be cleaned periodically. Rinse it with clean
water, and then place it back in the adapter.
Cleaning Nozzles
• A clogged or partially clogged nozzle can cause
significant reduction of water pressure coming out
of the nozzle and/or cause the unit to pulsate while
spraying.
• Turn off the unit.
• Turn off the water supply to the unit.
• Relieve any pressure trapped in the hose by
squeezing the trigger 2-3 times, and then lock the
spray gun by pushing the lock button from left to right.
• Remove the lance from the spray gun
• Using the nozzle tip cleaner provided (or an unfolded
paper clip), insert the wire into the nozzle hole and
move back and forth until debris is dislodged.
• Tap quick connect end of lance on hard surface
several times
• Back flush water through the nozzles using garden
hose and highest pressure available (either standard
water nozzle or use your thumb over the nozzle to
create water pressure for back flush).
15ANR011 AR240S_1700PSI ENG-FR-SP.indd 13
16/12/17 下午1:43
detergent on a dry surface. DO
NOT pre-soak area. Wetting the
surface first dilutes the detergent
and reduces its cleaning ability.
DO NOT allow detergent to dry on
surface. On vertical surfaces being
cleaned, apply detergent to lower
surfaces and work your way up to
prevent detergent from causing
streaks in the dirt and grime. Rinse
detergent by pressure washing
from bottom up for same reason.
• If a stain is particularly tough, it
may be necessary to reapply the
detergent and use a bristled brush
to scrub the stain. Subsequent
power washing after brushing
should successfully complete your
cleaning job.
Cleaning Garden Hose Adapter
• The screens inside the clear garden
hose adapter should be cleaned
periodically. Rinse it with clean
water, and then place it back in the
adapter.
Cleaning Nozzles
• A clogged or partially clogged
nozzle can cause significant
reduction of water pressure coming
out of the nozzle and/or cause the
unit to pulsate while spraying.
• Turn off the unit.
• Turn off the water supply to the unit.
• Relieve any pressure trapped in the
hose by squeezing the trigger 2-3
times, and then lock the spray gun
by pushing the lock button from left
to right.
• Remove the lance from the spray
gun
• Using the nozzle tip cleaner
provided (or an unfolded paper clip),
insert the wire into the nozzle hole
and move back and forth until debris
is dislodged.
• Tap quick connect end of lance on
hard surface several times
• Back flush water through the nozzles
using garden hose and highest
pressure available (either standard
water nozzle or use your thumb over
the nozzle to create water pressure
for back flush).
1
2
