background image

6

BEPOWEREQUIPMENT.COM

WARNING

Serious injury may occur from touching the gasoline engine, muffler, or heat exchanger. 

These areas can remain hot for some time after the pressure washer is shutdown.

• 

Never allow any part of your body to contact the gasoline engine, muffler, or heat exchanger.

WARNING

Serious injury may occur to the operator from moving parts on the pressure washer.

• 

Before making any adjustments, be certain the engine is turned off and the ignition cable(s) is removed 

from the spark plug(s). Turning the machinery over by hand during adjustment or cleaning might start 

the engine and machinery with it.

• 

Do not operate the unit without all protective covers in place.

WARNING

Serious injury may occur from a pressure washer malfunction or exploding accessories if 

incorrect system components, attachments, or accessories are used. 

Serious injury or death may occur if attempting to start the pressure washer when the 

pumping system is frozen.

• 

Never make adjustments to the factory set pressures.

• 

Never exceed manufacturers maximum allowable pressure rating of attachments.

• 

Do not allow any hoses to make contact with heat exchanger to prevent the possibility of bursting. Avoid 

dragging the hoses over abrasive surfaces such as cement.

• 

Use only manufacturer recommended repair parts for your pressure washer.

• 

In freezing temperatures, the unit must always be warm enough to ensure there is no ice formation 

in the pump. Do not start the pressure washer if it has been transported in an open or under heated 

vehicle without first allowing the pump to thaw.

WARNING

Serious injury or death may occur from detergents contacting the skin.

Serious injury can occur from loose debris being propelled at a high speed from the spray gun.

Injury may occur if the operator loses their balance caused by the thrust of water traveling 

through the spray nozzle.

• 

Never use any solvents or highly corrosive detergents or acid type cleaners with this pressure washer.

• 

Protective equipment such as rubber gloves and respirators are advisable, especially when using 

cleaning detergents.

• 

Keep all detergents out of the reach of children!

• 

Always wear protective goggles when operating the unit to shield the eyes from flying debris 

 

and detergents.

• 

Do not direct spray toward fragile materials such as glass.

• 

Stay alert: watch what you are doing. Do not operate the unit when fatigued or under the influence of 

alcohol or drugs.

• 

Never squeeze the trigger unless securely braced.

• 

Do not overreach or stand on unstable support.

• 

Wet surfaces can be slippery. Wear protective foot gear and keep good footing/balance at all times.

• 

Never pull the trigger of the gun while on a ladder, roof, or other unstable surface.

• 

Always hold on firmly to the gun/lance assembly when starting and operating the unit. Failure to do so 

can cause the lance to fall and whip dangerously.

• 

Do not leave pressurized unit unattended. Shut off the pressure washer and release trapped pressure 

before leaving.

• 

Do not operate the unit if you see any fuel, oil, or water leaking from the machine. DO NOT resume 

operation until the unit has been inspected and repaired by a qualified technician.

• 

Do not transport the unit by pulling on hoses or cords.

IMPORTANT SAFETY WARNINGS

Summary of Contents for HW2765HG







































































































Reviews: