background image

BE-VBM220 USER MANUAL     

3

IMPORTANT SAFETY INFORMATION 

Safety At All Times 

Thoroughly read and understand the instructions given in this manual before operation. Refer to the “Safety 

Decal” and read all instructions noted. 
Do not allow anyone to operate this equipment who has not fully read and comprehended this manual and 

who has not been properly trained in the safe operation of the equipment. 
• Operator should be familiar with all functions of the unit. 
• Operate implement from the driver’s seat only.
• Make sure all guards and shields are in place and secured before operating the implement.
• Do not leave tractor or implement unattended with engine running. 
• Dismounting from a moving tractor could cause serious injury or death. 
• Do not stand between tractor and implement during hitching.
• Keep hands, feet, and clothing away from power-driven parts. 
• Wear snug fitting clothing to avoid entanglement with moving parts.
• Watch out for wires, trees, etc., when raising implement. Make sure all persons are clear of working area.
• Turning tractor too tight may cause implement to ride up on wheels. This could result in injury or 

equipment damage.

Look For the Safety Alert Symbol 

The SAFETY ALERT SYMBOL indicates there is a potential hazard to personal safety involved and extra 

safety precaution must be taken. When you see this symbol, be alert and carefully read the message that 

follows it. In addition to design and configuration of equipment, hazard control and accident prevention 

are dependent upon the awareness, concern, prudence and proper training of personnel involved in the 

operation, transport, maintenance and storage of equipment. 

Be Aware Of Signal Words 

A signal word designates a degree or level of hazard seriousness. The signal words are: 

DANGER 

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This 

signal word is limited to the most extreme situations, typically for machine components that, for functional 

purpose, cannot be guarded. 

WARNING 

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury, and 

includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe 

practices. 

CAUTION 

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It 

may also be used to alert against unsafe practices. 

For Your Protection 

• Thoroughly read and understand the “safety label” section, read all instructions noted. 

Shutdown And Storage 

• Lower machine to ground, put tractor in park, turn off engine, and remove ignition key. 
• Detach and store implements in an area where children normally do not play. Secure implement by using 

blocks and supports. 

Use Safety Lights And Devices 

• Slow moving tractors, self-propelled equipment, and towed implements can create a hazard when driven 

on public roads. They are difficult to see, especially at night.

• Flashing warning lights and turn signals are recommended whenever driving on public roads. Use lights 

and devices provided with implement. 

Summary of Contents for AGRI EASE BE-VBM220



















Reviews: