manualshive.com logo in svg

BDI LINEA 5801, Instruction Manual

Share
Download
BDI LINEA 5801 Instruction Manual Download Page 38

38  |  BDIUSA.COM

LINEA 5801(A) / 5802(A)

The doors on your cabinet should be evenly 
spaced, and the doors should open and close 
freely without rubbing against the door frame. 
If the cabinet’s doors appear out of alignment, 
this condition can be corrected with minor 
adjustments to the European hinges on each 
door. Because these hinges are adjustable, adjusting one hinge can sometimes cause the need for 
adjustments to other hinges. But with a few adjustments, you can modify the orientation of the 
cabinet doors to make sure that they hang perfectly within your cabinet.

Use a 

(T1) Phillips Screwdriver

 to adjust the door hinges: 

n

  By adjusting 

Screw 1

, the door will move LEFT or RIGHT within the frame. Make minor 

adjustments at both top and bottom hinges for best results. 

n

  By loosening both 

Screws 2

 on both hinges, the door can move UP or DOWN. Retighten the screws.

n

  By adjusting 

Screw 3

 the entire door will move IN or OUT, opening or closing the gap between 

the door frame and cabinet. (This screw rarely needs adjustment.)

1

2

3

ADJUST DOOR HINGES (IF NEEDED)

FINE TUNING

PART/DESCRIPTION

QTY

T1-PHILLIPS 

SCREWDRIVER

1

Summary of Contents for LINEA 5801









































Reviews:

No comments

Brands by name

Popular brands

Load more brands