Bay Tek Games Big Bass Wheel Pro Troubleshooting Manual Download Page 10

 
 

Door Open Error 

 

There are 5 switches total: 
1 in back, 1 in left side door, 1 in right side door, 1 in left front door, and 1 in right front door. 

 

What happens if door is open? 

Tickets will not dispense. 
Game will not start. 
Auto spin will not engage 
Player can not spin wheel 

 

Handle will still move solenoid assy. – Make sure to remove handle when working on 
game! 

 

Door switches are Push/Pull type 
   

Switch can be pulled out when door is open and game will think door is closed. 

 

Troubleshooting Door Open Problem: 

 

 
 

Door Open 
message stays. 

 

a.  Faulty door switch. (A5SW7000) – It could be anyone of the five. 

 

b. 

Check all wires on switches.

 

 

c. 

Check crimps on wires.

 

 

d. 

Check connection to I/O Board

  

 

e.  Replace I/O board if needed. 

 

 

 
 
 
 

Open all 
5 doors 
and pull 
all 5 
switches 
out. 

 

Door Open 
message 
clears. 

 

a.  Individually check each switch by pushing in on each switch one by 

one and verify the door open message is not on screen. 

 

b.  If a door switch shows the message when pushed in, that switch is 

faulty. Replace switch (A5SW7000) 

   

 

   Front Right Side Door

 

        

Front Left Side Door 

 

   Back Door

 

 
 
 
 
 
 
 

 

         Right Game Side Door 

 

 

 

 

Left Game Side Door

 

 

 
 
 

AACE1602 

AACE1603 

AACE1601 

AACE1602 

AACE1600 

AACE1604 

AACE1600 

AACE1601 

AACE1603 

AACE1604 

This is a safety matter and switches 
must not be disabled or injury to 
player or technician may occur. 

 

Summary of Contents for Big Bass Wheel Pro



















Reviews: