Bay Networks 58000 Installation And Reference Manual Download Page 94 | Manualshive

Page: 94 / 158

background image

Installing and Removing the Model 58000 Switch

4-4

893-878-B

Installing an Expansion Module on the Model 58000 Switch

The Model 58000 switch has one MDA slot plus a plug-in card slot for
installing the MDA expansion module or another expansion module when
available. The MDA expansion module holds up to four additional MDAs.
MDAs can be added to any of the available connectivity slots on the MDA
expansion module.

Installing the Model 58000 Switch into the Model 500x Chassis

The Model 58000 switch is a double-wide module that you can install in the
Model 5000 or Model 5005 chassis. Install the Model 58000 switch in any two
consecutive slots on the chassis.

After you install the switch, the switch software identifies the location of the
switch as the higher number slot. For example, if the switch is installed in slots
one and two, the switch software locates the switch in slot two.

To install the Model 58000 switch into the Model 500x chassis, follow these
steps:

1.

Remove the filler panels from the chassis slots where you will install
the switch.

2.

Make sure the inserter/extractor levers are in their fully extended
positions.

3.

Slide the switch into two slots in the chassis until you feel it engage the
backplane connector. Carefully push the switch into place (see

).

NOTE:

Refer to the documentation that shipped with your expansion module

for specific instructions about installing it on the switch. Refer to the
documentation that shipped with your MDA(s) for specific instructions about
installing an MDA on the MDA expansion module.

CAUTION:

Connecting a switch to a switch community affects all switches in

the community. All other switches will transition to a configuring mode.
During this time, the switches will not forward any frames.

893-878-B Book Page 4 Monday, May 12, 1997 2:06 PM

«
...
92
93
94
95
96
...
»

Summary of Contents for 58000































































































































































Reviews:

No comments

Related manuals for 58000

PowerLine DHP-W611AV

Brand: D-Link Pages: 78

OCTOPUS 5TX-EEC

Brand: Hirschmann Pages: 6

Brand: Netis Pages: 16

Brand: axing Pages: 52

Media Board D/120JCT-LS-EW

Brand: Dialogic Pages: 2

Brand: NKE Pages: 15

FlexNetwork 5130 Series

Brand: HPE Pages: 33

Elinx EIR508 Series

Brand: B&B Electronics Pages: 2

Brand: Symantec Pages: 100

Brand: ADDON Pages: 4

Brand: Acces Pages: 21

Brand: Hame Pages: 37

Brand: ST Pages: 37

Brand: TRENDnet Pages: 205

Brand: ADTRAN Pages: 4

Brand: TRENDnet Pages: 2

Brand: Devolo Pages: 24

Brand: Planet Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands