manualshive.com logo in svg

Bay Networks 58000, Installation And Reference Manual

Share
Download
Bay Networks 58000 Installation And Reference Manual Download Page 95

Connecting Cables

893-878-B

4-5

 

Figure 4-2.

Inserting the switch into the chassis

4.

Rotate the inserter/extractor levers toward each other to seat the 
backplane connectors.

5.

Align and finger-tighten the captive mounting screws. Finish 
tightening them with the flat-tip screwdriver.

Connecting Cables

When the Model 58000 switch has been installed in the chassis, connect cables 
as needed to the 10 Mb/s built-in ports on the front panel of the switch or to the 
additional 100 Mb/s MDA ports when MDAs are installed in the switch. See 

Connecting Individual Workstations, Servers, and Other Ethernet Devices

 in 

Chapter 5, “Connecting to the Network,” for instructions on connecting cables 
to the switch.

When you have completed all cable connections, continue with 

Verifying the 

Installation

 next in this chapter.

NOTE: 

The switch is a double-wide module. It can occupy any two 

consecutive slots of the 14 slots on the Model 5000 chassis, or any two 
consecutive slots of the eight slots on the Model 5005 chassis.

Model 5000

6182

Inserter/extractor
lever

Captive retaining
screw

893-878-B Book  Page 5  Monday, May 12, 1997  2:06 PM

Summary of Contents for 58000































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands