Bay Networks 58000 Installation And Reference Manual Download Page 76 | Manualshive

Page: 76 / 158

background image

Planning a Switched Network

2-38

893-878-B

For more information about connecting Model 58000 switches together, see

Connecting Model 58000 Switches Together

in Chapter 5, “Connecting to the

Creating Trunk Links

The Model 58000 switch recognizes all connections to other Model 58000
switches (through “Auto” mode ports) as trunk links. These links can exist
between MDA 100 Mb/s ports provided that the proper cables are attached.
Although it is physically possible to configure 10 Mb/s point-to-point
connections between any two Model 58000 switches, this configuration is not
supported. This type of configuration can introduce instabilities in the network.
For more information, see

earlier in this chapter.

describes the possible port configurations and operating modes of

Model 58000 switch ports (built-in 10BASE-T ports and 100BASE-T MDA
ports).

Table 2-2.

Port configurations and operating mode

MDA or
built-in port

Default operating mode Configuration options

10BASE-T
built-in port

Default mode = 10 Mb/s
half-duplex

Configurable to operate at 10 Mb/s
full-duplex mode. If the port is not
connected to the backplane, it can
operate in half- or full-duplex. (Ports 1–12
can be configured only for half-duplex
when connected to System 5000
backplane.)

100BASE-FX
MDA port

Default mode = 100 Mb/s
half-duplex; flow control
enabled

Configurable to operate at 100 Mb/s
full-duplex. Flow control can be disabled
as a configuration option.

100BASE-TX
MDA port

Default mode = 100 Mb/s
half-duplex; flow control
enabled

Configurable to operate at 100 Mb/s
full-duplex. Flow control can be disabled
as a configuration option.

893-878-B Book Page 38 Monday, May 12, 1997 2:06 PM

«
...
74
75
76
77
78
...
»

Summary of Contents for 58000































































































































































Reviews:

No comments

Related manuals for 58000

Brand: D-Link Pages: 267

Brand: H3C Pages: 1057

Brand: Parker Pages: 344

Express5800/E120d-M

Brand: NEC Pages: 2

Brand: PaloAlto Networks Pages: 3

Brand: Lanner Pages: 109

Brand: B&B Electronics Pages: 2

Brand: H3C Pages: 9

Brand: Zoom Pages: 31

Brand: Hawking Pages: 21

TGXPS-1080-M12-MV Series

Brand: ORiNG Pages: 2

Brand: Orcon Pages: 2

3224 Diamond Edge

Brand: Patton electronics Pages: 2

Brand: NETGEAR Pages: 2

CONNECT Box Pro

Brand: ratiotec Pages: 12

Brand: Linksys Pages: 37

Brand: B&B Electronics Pages: 90

Brand: B&B Electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands